The hollow circle cross section of the simply supported beam shown in the figure. Find the maximum flexural stress if :the uniform distributed load is 80 lb/ft -80 lb/ft 10 ft O 4 in C 2.5 in 1000 psi O 170.38 psi O 281.7 GPa 281.7 psi non of them 281.7 MPa O 1000 MRo

The hollow circle cross section of the simply supported beam shown in the figure. Find the maximum flexural stress if :the uniform distributed load is 80 lb/ft -80 lb/ft 10 ft O 4 in C 2.5 in 1000 psi O 170.38 psi O 281.7 GPa 281.7 psi non of them 281.7 MPa O 1000 MRo

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

1. A Steam Turbine Generator (STG) has a mass of 100 tons. What will be the bearing stress of the STG to the soil if it has a foundation dimension of 15 meters by 10 meters. 2. A paper below has a shear strength of 10 MPa. What must be the applied force to cut the paper into two? 0.001mm 241mm 3. A beam with a maximum moment of 20kN-m has a height of 20mm and a width of 15mm. Determine the flexural/bending stress at the beam.
1. Find the internal force of member EG, FH, and FG using method of sections. 0.866 m 3KN 5 @ 1m
For the given fig find the correct representation of the longitudinal variation of the bending stress
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Calcuate Bending From Point A to Point B and Point A to Point C also Torsion from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
2. Figure (a) shows the cross section of a column that uses a structural shape known as W8 x 67 (wide-flange beam, nominally 8 in. deep, weighing 67 Ib/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7 in², Ix =272 in“, and ly =88.6 in4. Figure (b) shows the cross-sectional dimensions for the structural steel section known as C10 x 20 (channel with a nominal depth of 10 in., weighing 20 Ib/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88 in?, Ix =78.9 inª, and ly =2.81 in*. If a W8 x 67 section is joined to a C10 × 20 section to form a structural member that has the cross section shown in Figure (c), a. Locate the centroid of the built-up section in the Figure (c). b. Calculate the centroidal moments of inertia, Ix and ly for this cross section. 事士 0.606 in. 0.933 in. y Web in. --0.575 in. 10 in. - Flange -- 0.379in.…
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ib/ft 6 ft ft 6 ft 12 ft ft ANS: T = Ib, Stress = ksi
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
The beam is supported by a pin at point A and a roller at point C. A distributed load is applied to the beam. Neglect the weight and thickness of the beam. Hints: 1. will need to use similar triangles to find the height after sectioning at B. 2. Review direction of normal force, shear force and bending moment and which is positive or negative. W2 W1 A di d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value W1 190 N-m W2 440 N-m di 5 m d2 5 m a. Determine the magnitude of the normal force at point B, NB. . b. Determine the magnitude of the shear force at point B, VB- c. Is the shear force VB a positive or negative shear force? d. Determine the magnitude of the bending moment at point B, MB. e. Is the bending moment MB a positive or negative bending moment? Round your final answers to 3 significant digits/figures.
A 0.5kg weight is hung from the end of a cantilever beam, causing a vertical displacement of y = -0.01 inches relative to no load. The weight is increased to 1.0kg. What is the new displacement relative to no load? Typed and correct answer please. I ll rate
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm