The generating set lines L1 and L2 are connected to bus-bar A. L2 is supplied from a powerful system and L1 is supplying an important industrial plant. A fault is detected in CB1; preventing the circuit from opening, explain how the voltage at CB1 can be reduced to zero, so that repair can be carried out, without interrupting the supply to the important industrial plant.

The generating set lines L1 and L2 are connected to bus-bar A. L2 is supplied from a powerful system and L1 is supplying an important industrial plant. A fault is detected in CB1; preventing the circuit from opening, explain how the voltage at CB1 can be reduced to zero, so that repair can be carried out, without interrupting the supply to the important industrial plant.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.36P

See similar textbooks

Similar questions

Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
The Electricity Company of Ghana (ECG) has set up a system for reporting power supply faults in the Greater Kumasi Area, including high or low voltage and frequent power outages. Customers can contact ECG customer service and report their issue, providing their ECG pole reference number. The faults are recorded and sent to the ECG Fault Office for action. However, there is a delay in resolving the faults, and clients have to make several follow-up calls to check on the status of their complaints. The ECG management team conducted a survey and found out that customers want their faults resolved within three hours, and any delay beyond that is unacceptable. The team is looking for a solution that will offer a seamless experience to customers and minimize time and effort wasted. a) Given the information above, and making reasonable assumptions, model the current (‘AS IS’) and explain business processes at ECG Fault Office.…
The Electricity Company of Ghana (ECG) has set up a system for reporting power supply faults in the Greater Kumasi Area, including high or low voltage and frequent power outages. Customers can contact ECG customer service and report their issue, providing their ECG pole reference number. The faults are recorded and sent to the ECG Fault Office for action. However, there is a delay in resolving the faults, and clients have to make several follow-up calls to check on the status of their complaints. The ECG management team conducted a survey and found out that customers want their faults resolved within three hours, and any delay beyond that is unacceptable. The team is looking for a solution that will offer a seamless experience to customers and minimize time and effort wasted. a) Given the information above, and making reasonable assumptions, model the current (‘AS IS’) and explain business processes at ECG Fault Office. b)What would the future state (ASTOBE) look like?Provide a new…
Explain the concept of electrical grid reliability and its importance.
Explain the concept of Fault Ride-Through (FRT) capability in wind power generation systems. How do wind turbines maintain grid stability and continue operation during grid faults? Discuss the role of control strategies and grid codes.
C.Comments on this statement: "PMUs can be used as a protective relays”. D. What is the ZIB and it role in OPP E Is there any effect of existence of HVDC transmission lines in OPP and state estimations? F. Discuss the challenges that might face application of PMUS/WAMs in any given power system.
The single line diagram of a power system is shown in Figure Q2.1 includinggenerator and transformer winding connection and earthing details. The parametersfor this system have been calculated on a common 100 MVA base and are given inTable Q2.1. All resistances and shunt susceptances are neglected. This systemexperiences a single line to ground fault at a point F on line L1. The point F is at adistance d from Bus 4 along the line L1. The total length l of the line L1 is 50 km.Note that the location of d is not drawn to scale in Figure Q2.1. The fault current atthe fault point F is measured to be 6.106 kA. i) Determine the zero, positive, and negative sequence Thevenin equivalentimpedances as seen at the fault point F. These should be evaluated in per unitand shown as a function of d.ii) Use the sequence impedances calculated in part (i) to determine the distance dof the fault (in km) from Bus 4. It's different from the answer, please don't send it
Describe the concept of fault current analysis in power systems and its role in protecting electrical equipment.
Contribution of fault analysis in power system netwrok?
The single line diagram of a power system is shown in Figure Q2.1 including generator and transformer winding connection and earthing details. The parameters for this system have been calculated on a common 100 MVA base and are given in Table Q2.1. All resistances and shunt susceptances are neglected. This system experiences a single line to ground fault at a point F on line L1. The point F is at a distance d from Bus 4 along the line L1. The total length ?? of the line L1 is 50 km. Note that the location of ?? is not drawn to scale in Figure Q2.1. The fault current at the fault point F is measured to be 6.106 kA. i) Determine the zero, positive, and negative sequence Thevenin equivalent impedances as seen at the fault point F. These should be evaluated in per unit and shown as a function of d.ii) Use the sequence impedances calculated in part (i) to determine the distance d of the fault (in km) from Bus 4.
Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and the motors are as shown in the figure. The reactance of lines 1 and 2 are 40 ohms and 50 ohms respectively. Assume that system is unloaded, and the generators are generating their rated voltage. Select the generator G₁ ratings as base values. Choose the fault location in bus 1 And give the below answers For a symmetrical three phase fault on the bus (a).Determine the Thevenin's equivalent circuit which can be used to calculate the fault current. (b) Calculate the fault current contribution from the generator connected to the bus on which you have selected for fault calculation
Explain the concept of fault analysis in power systems and how it helps in ensuring system reliability.