The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at a constant output speed of Nout = 2391 rpm. OUTPUT SHAFT 1 TORQUE 750 N*m COMPOUND GEAR 3 30 ТЕЕТН COMPOUND OUTPUT GEAR 2 25 ТЕЕТH COMPOUND INPUT GEAR 1 18 ТЕЕТH COMPOUND DRIVER GEAR O 15 TEETH GEAR 4 15 TEETH COMPOUND GEAR 5 20 TEETΗ МОTOR OUTPUT SHAFT 2 TORQUE 750 N*m SPEED Nout RPM Determine the a) Motor/input torque b) Motor/input speed c) Motor/input horsepower input

The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at a constant output speed of Nout = 2391 rpm. OUTPUT SHAFT 1 TORQUE 750 Nm COMPOUND GEAR 3 30 ТЕЕТН COMPOUND OUTPUT GEAR 2 25 ТЕЕТH COMPOUND INPUT GEAR 1 18 ТЕЕТH COMPOUND DRIVER GEAR O 15 TEETH GEAR 4 15 TEETH COMPOUND GEAR 5 20 TEETΗ МОTOR OUTPUT SHAFT 2 TORQUE 750 Nm SPEED Nout RPM Determine the a) Motor/input torque b) Motor/input speed c) Motor/input horsepower input

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

no Qt+ A Compound gear train Consists of 6 gears. No of teeth : A B D E 60 40 35 28 50 30 shaft on another shaft. The Gears B $ C are on One while are gears Gear A drives B, gear gear c drives, gear s gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2z State advkitages of Cycloidal In volute profile as a gear tooth pnfile.
Answer d and e
In a spur gear arrangement, the driver has 70 teeth of 26 mm pitch. Find the power, if it can transmit a tangential force of 100 N. Take speed of driver as 160 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
solve, show all steps for given solution
I want to solve these five points
Determine the speed of the gear F
Pls explain to step by step and i will rate your answer immediately. Thanks
6. 5 3 Arm 6. 2 Arm Arm 2 3 1 Bearing Given N2 = 30, N3 = 25, N4 =45, N5 = 40, N6 = 200 W2 = 240 rpm ccw, warm = 120 rpm cw, T2 = 12 ft-lb Show your work. Answers without work will not be accepted a. Identify the gear sets. b. Determine the velocity gear train ratio and the angular velocity of gear 6. c. Determine the torque gear train ratio and output torque of gear 6.
In the pulley system shown in the figure, while the P gear rotates in the direction of 1 with its angular velocity, find the direction and angular velocity values of the other gears. Hint: The speed of the gears is equal at the point of contact. The speed of a belt is the same at all points.( w=3 rad/s , rk=0.8m ,rL=0.2 m ,rM=0.2m, rN=0.5m rP=0.4m rR=0.4m
In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA-20;TB-60; Tc-140;TD-40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates C140 120 Output D 40 60 20 Input