Referring to the given figure, spur gear A receives 5 hp at 650 rpm thl B is an idler and gear C is the driven gear. The pressure angle o is 20° and the gear diameters: DA, DB, and DC are 6", 12", and 9" respectively. Determine : a. The torque each shaft must transmit, b. The tooth load for which each gear must be designed (Fr and Ft), c. The force applied to the idler shaft as a result of the gear tooth loads.

Referring to the given figure, spur gear A receives 5 hp at 650 rpm thl B is an idler and gear C is the driven gear. The pressure angle o is 20° and the gear diameters: DA, DB, and DC are 6", 12", and 9" respectively. Determine : a. The torque each shaft must transmit, b. The tooth load for which each gear must be designed (Fr and Ft), c. The force applied to the idler shaft as a result of the gear tooth loads.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q2-1 shows a schematic of the power train for 2012 Nissan Leaf pure electric cars, which includes a two stage gearbox (a compound train). The numbers of teeth of the gears in the gearbox are N1=N3=17, N2=31 and N4=74. The motor speed at an engine power of P = 80 kW is nmotor (n1) = 9,795 rpm. N2=31 T 2012 LEAF Driveline from Motor to Axle: 17T 31T N1=N3 =17 T 17T 74 T - Wheels I N4=74 T Motor Figure Q2-1 What are the necessary and sufficient requirements for the two stage gearbox to mesh properly for power transmission? i) Calculate the rotating speed (nwheel or n4) and the torque Twheel or T4 on the axle of the driven wheels. Neglect power loss of the gearbox. ii) nmotor(n1)=9,795 rpm in kilometre per hour? You may assume the diameter of the wheels to be D = Ø600 mm. What is the speed of the Nissan Leaf car when the motor speed is at AXLE AXLE
Answer d and e
solve, show all steps for given solution
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20 3 = 30, 2, = 50 . Calculate the module of four gears and the tooth number of gear 1.
In the pulley system shown in the figure, while the P gear rotates in the direction of 1 with its angular velocity, find the direction and angular velocity values of the other gears. Hint: The speed of the gears is equal at the point of contact. The speed of a belt is the same at all points.( w=3 rad/s , rk=0.8m ,rL=0.2 m ,rM=0.2m, rN=0.5m rP=0.4m rR=0.4m
The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears 40 teeth 490⁰ B 70 teeth 50 teeth
A simple gear train has 2 spur gears. The input gear has 24 teeth and the output gear has 106 teeth. The input rotates at 1,556 rev/min clockwise. Calculate the gear ratio and the output speed in rev/min. The input torque is 17 15 Nm and the efficiency is 0.8465%. Use speeds from the previous question to calculate the absolute value of the holding torque in Nm.