Parvinbhai !Required InformationA gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with thetransmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft anddelivered through gear B through a transmitted force Fg at the pressure angle shown. Assume the gear ratio from gear Bto its mating gear is 3 to 1. Also assume that gears are full-depth.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.FA-11 kN20°400 mmGear A, 600-mm dia.The new force FA, newISThe new force FB, new s350 mmGear B, 300-mm dia.KN.300 mmSuppose the 20° pressure angle for gear A and gear B is exchanged for a gear with 25° pressure angle while maintaining the samepitch diameters and module, determine the new forces FA and Fg If the same power is to be transmitted.kN.50-mm dia.

The force transmitted on gear A is .The pressure angle given for gear A is .The pressure angle…

ed force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and through gear B through a transmitted force Fg at the pressure angle shown. Assume the gear ratio from gear Ing gear is 3 to 1. Also assume that gears are full-depth. his is a multi-part question. Once an answer is submitted, you will be unable to return to this part.

ed force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and through gear B through a transmitted force Fg at the pressure angle shown. Assume the gear ratio from gear Ing gear is 3 to 1. Also assume that gears are full-depth. his is a multi-part question. Once an answer is submitted, you will be unable to return to this part.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mercury has high specific heat. Select one: O True O False
8
Define the international system of units.
Calculate the rate of flow of waste thermal energy out of the engine in the exhaust gases in kW (to 1 decimal point). If the air inlet temperature is 35 °C, the air to fuel ratio is 10:1, the inlet air mass flow rate is 37 kg/hr, the specific heat capacity of exhaust gas is 1.13 kJ/kg/K, and the exhaust temperature is 500 °C. Add your answer Integer, decimal or E notation allowed
Can I have the formula for the percent difference?
dy 15 MPa 50
Q.7 Degree of freedom at triple point is A В D -1
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values
Answer it correctly please. I will rate with 2-3 votes.
What is the swept volume of a 6 cylinder compressor with a piston diameter of 3 3/8inch and a length of 8 7/8 inch turning at 1700 RPM ? Note* I posted this question and someone answered wrong and everything out of order, please don't answer if you don't know, i just need help.
Te-Learning Portal Courses Reports e-Services Which of the following statement is correct Select one: of O Fiction is very bad at rough surfaces ion O Friction is zero for smooth surfaces O Friction is good at smooth surfaces O Friction is high for rough surfaces