The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 1.8 MPa. The tank and the 25-mm-diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m.

The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 1.8 MPa. The tank and the 25-mm-diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cable is attached to the boom at A and to point B as shown in (Figure 1) so that x = 60 ft, y = 40 ft, and z = 40 ft. Figure x A B 1 of 1 ▼ Part A Determine the length of the cable. Express your answer in feet to three significant figures. TAB= 82.5 ft Submit Correct Part B Previous Answers Determine the angle between the positive z axis and the cable. Express your answer in degrees to three significant figures. V— ΑΣΦ Y= 60.983 vec Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 3 attempts remaining
Solve for the indicated value, and graph the situation showing the solution point. The formula for measuring sound intensity in decibels D is defined by the equation D = 10 log (1) using the common (base 10) logarithm where I is the intensity of the sound in watts per square meter and Io = 10-12 is the lowest level of sound that the average person can hear. How many decibels are emitted from a jet plane with a sound intensity of 8.7. 102 watts per square meter? Round your answer to three decimal places. The jet plane emits Number decibels at 8.7. 102 watts per square meter. Select the correct graph of the situation showing the solution point. 200 D 150 100- 50 400 800 1200 1600 2000 400 800 1200 1600 2000 O O 0 200D 150- 100 50 0 200- Subr
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 360.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.30 MN. pressure vessel W bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x10 X
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.
Phi = 40 degrees Theta = 35 degrees F1 = 425 Newtons Alpha = 60 degrees Beta = 45 degrees F2 = 625 Newtons F1 F2 Find the y-component of F2 in Newtons. If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign.
pivot X 30° F As shown in the diagram above (viewed from above), force F of magnitude 882 N is exerted on a rod which is pivoted about its center a distance 0.7 from the pivot. Calculate the torque exerted by force F. Express your answer in N*m and round to the nearest tenth (1 decimal). Enter a negative answer for a clockwise torque and a positive answer for a counterclockwise torque.
Question 1. W₂ y: ← WI Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown above (not drawn to scale). The bottom section has width w₁ = 10mm and height h₁ = 60mm. The top section has width w₂ = 50mm and height h₂ = 14mm. Enter your answer in millimetres correct to two decimal places. mm hi Type here to search 122 4313 O Af
Use the information given in the figure below. When the supporting posts are removed, calculate the magnitude of the following: the torque on each side and the net torque of the balancing beam. Reminder: Force is not equal to mass. (g=9.8m/s²) 175 15 1251075 05 029 Meters ozs as o7s 125 Meters Express all your answers in whole numbers. T+ Nm Nm Tnet Nm
Three forces act on the bracket as shown in (Figure 1). The resultant force is directed along the positive x' axis and has a magnitude of 7.7 kN. Figure 4 kN 15⁰ 30⁰ 6 kN 1 of 1 Determine the magnitude of F. Express your answer to three significant figures and include the appropriate units. F = Submit Part B 0 = μA Submit Value Request Answer Determine the direction of F. Express your answer in degrees to three significant figures. G| ΑΣΦ Units ↓↑ vec Request Answer ? ?
In Exercises 25 and 26, find the magnitude of the torque exerted by F on the bolt at P if PQ = pounds. 8 in. and F = 30 lb. Answer in foot- %3D 25. 26. 135° F 60°
In (Figure 1), set F= 300 N. Figure H 60° F₁-500 N Part A Determine the magnitude of the resultant force acting on the hook Express your answer to three significant figures and include the appropriate units. FR- Submit Part B 0- Submit MÅ Value Provide Feedback Request Answer Determine the direction of the resultant force measured clockwise from the positive z axis Express your answer in degrees to three significant figures. 195) ΑΣΦ Units i vec Request Answer ? ?
Phi = 41 degrees Theta = 36 degrees F1 = 400 Newtons Alpha = 59 degrees Beta = 44 degrees F2 = 300 Newtons F2 Find the x-component of F1 in Newtons. Find the y-component of F1 in Newtons. Find the z-component of F1 in Newtons. If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign.