The following test results of a single-phase step-down transformer which were measured at primary side: Open Circuit Test: Voc= 415V; loc= 0.22A; Poc= 7.64W; Vo=240V Short Circuit Test: Vsc= 25.2V; Isc= 18.07A; Psc= 142.43W 7. An inductive load was then connected to the step down transformer and recorded that the full load output current Is = 31.25A. Determine: a. Equivalent resistance of the transformer referred to the primary circuit Req and equivalent reactance of the transformer referred to the

The following test results of a single-phase step-down transformer which were measured at primary side: Open Circuit Test: Voc= 415V; loc= 0.22A; Poc= 7.64W; Vo=240V Short Circuit Test: Vsc= 25.2V; Isc= 18.07A; Psc= 142.43W 7. An inductive load was then connected to the step down transformer and recorded that the full load output current Is = 31.25A. Determine: a. Equivalent resistance of the transformer referred to the primary circuit Req and equivalent reactance of the transformer referred to the

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.56P: Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
1.a. For performing dielectric-strength tests on insulating materials, two transformers are connected in aA. parallel combination.B. cascade arrangement.C. polyphase arrangement. 1.b. In large power transformers, the unequal voltage distribution caused by voltage surges in the winding isprevented by the use ofA. static shields.B. series capacitors.c. low-voltage arresters.
Two 11,000/2,200-V, 1-phase transformers are connected in parallel to supply a total load of 200 at 0.8 p.f. lagging at 2,200 V. One transformer has an equivalent resistance of 0.4 ohms and equivalent reactance of 0.8 ohms referred to the low-voltage side. The other has equivalent resistance of 0.1 ohms and a reactance of 0.3 ohms. Determine the current and power supplied by each transformer.
What is the influence of transformer connections in single-phase transformers connected for 3- phase operation
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
What are the uses of three-phase transformers?
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
For performing dielectric-strength tests on insulating materials, two transformers are connected in a A. parallel combination.B. polyphase arrangement.C. series combination. D. cascade arrangement.
The ratings of a single-phase three-winding transformer are as follows:*primary winding: 300 MVA, 14kV*secondary winding: 300MVA, 200kV*tertiary winding: 40MVA, 20kV. The leakage reactances are:*Xps = 0.1 at 300MVA, 14kV*Xpt = 0.16 at 40MVA, 14kV*Xst = 0.14 at 50MVA, 200kV Neglecting the winding resistance and exciting current, calculate Xp, Xs and Xt using 300 MVA and 14kV as the base for the primary winding.
What is phase angle of voltage induced in primary and secondary windings of transformers due to mutial flux?
What are the conditions for the parallel operation of 1-phase transformers?
In no load phasor diagram of practical transformer, the magnetizing current Imag is with primary voltage Vp. 90° out of phase Leading by 30° Lagging by 60° In phase