Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 1000HZ. Var Band Stop uodny Pass Band Pass Band Frequency P) Low Pas Response High Pa Response Frequency ) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP, CHP) of 0.2uF, calculate the values of the two resistors, RLp and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1 fi 2nRLpCLP 2. From the High pass filter formula, Find RuP: 1 2nR#PCHP 3. Calculate the center frequency (fc) and Bandwidth (BW): a. fc = Vfi x fa b. BW = f# - fi

Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 1000HZ. Var Band Stop uodny Pass Band Pass Band Frequency P) Low Pas Response High Pa Response Frequency ) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP, CHP) of 0.2uF, calculate the values of the two resistors, RLp and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1 fi 2nRLpCLP 2. From the High pass filter formula, Find RuP: 1 2nR#PCHP 3. Calculate the center frequency (fc) and Bandwidth (BW): a. fc = Vfi x fa b. BW = f# - fi

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.
Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
What is the function of a low pass filter? Draw a diagram of a simple low-pass filter using a capacitor and a resistor.
3. Show how a series RLC filter, its type depends on the output voltage terminal as follows: Low pass filter the output voltage across ... High pass filter the output voltage across . Band pass filter the output voltage across Band reject filter the output voltage across ...... ......... ........
For a given transfer function of a bandpass filter circuit as shown in the figure For a given transfer function (Take K as 1) Find the center frequency, band-with and the gain for this bandpass filter. 2.Find the cut-off frequencies and the quality for this filter
In the circuit below, determine the formula for the cutoff frequency if low-pass or high-pass or center frequency if bandpass/bandstop and determine the transfer function. Also show the type and order of the filter.
(b) Analyse and obtain the transfer function for the filter as shown in Figure Q2(b). R₁ VW HH R₂ W Figure Q2 (b)
What is a criteria to find low pass filters, bandpass filter and highpass filter from a pole zero plot?
In the circuit in the figure, Vin=30Vrms and Vout are taken from the C1 capacity. Accordingly, a) Filter find the type b) Find the cutoff frequency (fc) of the circuit c) A=Vout/Vin for f=100, 800 and fc values draw the curve?
[Q5] Choose appropriate values for this Sallen-Key high-pass filter circuit to give it a cutoff frequency of 7 kHz with a “Butterworth" response Draw the complete circuit diagram
Response curves for second-order filters are shown in Figure 3. Identify each as Butterworth, Chebyshev, or Bessel. (a) -40 dB/decade (b) (d) out V out -40 dB/decade decade
The mask shown in the figure below belongs to which type of filter : Median filterSharpening frequency filterSharpening spatial filterSmoothing spatial filter