Fast The following figures show the block diagram of a memory-based state machine with two inputs A and B and one output Z and the ASM chart that the state machine must implement:ل پلاتیaddressinputs0123SEL INV S1dkMUX33.MEMORYIncZo Z1MUXoutputZEهرZشرHow many states do we need to insert into the ASM chart in order to ensure a single branch address and that only one qualifier is tested between transitions ?0 1Z

According to the question, we need to find how many states we need to insert into the ASM chart in…

The following figures show the block diagram of a memory-based state machine with two inputs A and B and one output Z and the ASM chart that the state machine must implement: address inputs SEL INV S 1 MEMORY S H Zo Z₁ MUX output 7 How many states do we need to insert into the ASM chart in order to ensure a single branch address and that only one qualifier is tested between transitions ?

The following figures show the block diagram of a memory-based state machine with two inputs A and B and one output Z and the ASM chart that the state machine must implement: address inputs SEL INV S 1 MEMORY S H Zo Z₁ MUX output 7 How many states do we need to insert into the ASM chart in order to ensure a single branch address and that only one qualifier is tested between transitions ?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

question1:In a memory system, data is 16-bit wide. Break the information into bytes with their addresses using little endian and big-endian methods. Starting address is F800 and the data is: E0F2 0041 question2:What acknowledgment signals are there in I2C bus?
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!
Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller
3. Suppose r0=0x20000000 and r1=0x12345678. All bytes in memory are initialized to 0x00. Suppose the following assembly program has run successfully (the three instructions will be executed in the given order). Draw a table to show the memory value if the processor uses little endian. STR r1, [r0], #4 STR r1, [r0,#4]! STR r1, [r0, # 4] Address 0x20000010 0x2000000f 0x2000000e 0x2000000d 0x2000000c 0x2000000b 0x2000000a 0x20000009 0x20000008 0x20000007 0x20000006 0x20000005 0x20000004 0x20000003 0x20000002 0x20000001 0x20000000 Data
Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 ORAB #$EE (c) (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB (i) EORA #$E4 (G) ROR A
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)