Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 (c) ORAB #$EE (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB EORA #$E4 (i) (i) ROR A

Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 (c) ORAB #$EE (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB EORA #$E4 (i) (i) ROR A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q. To interface memory with the microprocessor, connect register the lines of the address bus must be added to address lines of the chip. A. single B. memory C. multiple D. triple
What Is the jobs done by registers inside a CPU
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
%VY l. In. O Homework1.pdf Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=0A00H, (DS)=OB00H, (SS)=OD0OH, (SI)=OFFOH, (DI)=00BOH, (BP)=00EAH and (IP)=0000H, LIST=00FOH, Ax=4020H, BX=250OH. 1) Destination operand of the instruction MOV LIST (BP+DI], AX 2) Source operand of the instruction MOV CL, (BX+200H] 3) Destination operand of the instruction MOV [DI+6400H], DX 4) Source operand of the instruction MOV AL, [BP+SI-400H] 5) Destination operand of the instruction MOV [DI+SP], AX 6) Source operand of the instruction MOV CL, (SP+200H] 7) Destination operand of the instruction MOV (BX+DI+6400H], CX 8) Source operand of the instruction MOV AL, [BP- 0200H] 9) Destination operand of the instruction MOV (SI), AX 10) Destination operand of the instruction MOV (BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [ВР+200H] 12) Source operand of the instruction MOV AL, [SI-0100H]…
Assuming that DI=10016, DS= 140016, SI=FF0016, BX= AE0016, AX=100616 and the memory contents explained in the Table1. Hand trace the execution of the following Table 1 program MOV SI, [BXx+33H] Memory Memory Address Content MUL SI 1EE30 92 ADD AL, DH 1EE31 EA CMP AL, 4E16 1EE32 F5 Then answer the following questions: 1EE33 62 1- What are the values of registers in each statement? 1EE34 22 2- What is the effect to the flag registers after execution ADD instruction in 1EE35 8B the third statement of the program? please,I need answer the question less than hour
e example to each one of application of microprocess.. 2/ Write the contents of flag register after execute the following operation (AC)16 + (3B)16-
Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit. The tpcg = 0.5 ns, tccq = 0.25 ns, tpd = 4 ns, tcd = 2.5 ns, tsetup = 0.5 ns and thold = 0.2 ns. What is the maximum value of fc? Select one: a. 0.2 ps O b. 200 MHz O c. 2 GHz O d. 200 KHz
1- Explain the meaning and operation of CMC instruction ? 2. The Instruction Pointer is bits in length. a) 8 bits b) 4 bits c) 16 bits d) 32 bits
17. Provide the starting and ending physical address values, in hexadecimal, for the entire 1/O register memory section for the ATmega2560. Beginning address = Ending address = 18. What are the differences between the standard and extended I/O register sections? 19. Provide the instructions needed to write one byte of data to an 1/O register in the 1) standard and 2) extended I/O register sections.
Microprocessor
JC mean jump to specific address when the CF in the flag bit is = b.two c.one a. zero d.three Overflow flag bit indicates overflow for a.Signed integer only. c. Signed and Unsigned integer only. The 8086 architecture consists pipeline processing. b. Two b. Three arithmetic operations. b. Unsigned integer only. d. Floating point. unit(s) work in parallel is called c.Four d. One
In the MIPS processor that is part of the PIC32 microcontroller, what is the length of each instruction? a.16 bits b. 24 bits c. 32 bits d. 64 bits