The flow rate in a 300 mm diameter pipeis 0.226 m³/s. The flow is known to beturbulent and the centerline velocity is3.66 m/s. The density of liquid flowing is900 kg/m³.850-Determine the friction factor.c) 0.03411d) 0.04158a) 0.02655b) 0.01168Determine the head loss per meterlength of pipe.a) 0.08 m.b) 0.06 m.-c) 0.02 m.d) 0.04 m.Determine the shearing stress at thewalls of the pipe.a) 12.71 N/m2c) 14.57 N/m²b) 17.54 N/m2 d) 16.47 N/m²

Answered: Image /qna-images/answer/7cb030da-c584-4578-82ff-55500c65a406.jpg

The flow rate in a 300 mm diameter pipe is 0.226 m³/s. The flow is known to be turbulent and the centerline velocity is 3.66 m/s. The density of liquid flowing is 900 kg/m³. 850 - Determine the friction factor. a) 0.02655 c) 0.03411 b) 0.01168 d) 0.04158 Determine the head loss per meter length of pipe. a) 0.08 m. b) 0.06 m. c) 0.02 m. d) 0.04 m. 3 Determine the shearing stress at the walls of the pipe. a) 12.71 N/m2 c) 14.57 N/m² b) 17.54 N/m2 d) 16.47 N/m²

The flow rate in a 300 mm diameter pipe is 0.226 m³/s. The flow is known to be turbulent and the centerline velocity is 3.66 m/s. The density of liquid flowing is 900 kg/m³. 850 - Determine the friction factor. a) 0.02655 c) 0.03411 b) 0.01168 d) 0.04158 Determine the head loss per meter length of pipe. a) 0.08 m. b) 0.06 m. c) 0.02 m. d) 0.04 m. 3 Determine the shearing stress at the walls of the pipe. a) 12.71 N/m2 c) 14.57 N/m² b) 17.54 N/m2 d) 16.47 N/m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A 20-mm diameter steel pipe , 30m long is used to drain an oil tank. Determine the discharge of the pipe when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f=0.012.
Problem 2: Comparing Three Equations for Head Loss Compare three equations for friction head loss in pipes, assuming constant friction factors. Recall the slope of the energy grade line (EGL) is S = he/L. Part A i. Write the Darcy-Weisbach equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, λ? iii. For constant 2, if the discharge is doubled, by what factor does the head loss increase? Part B i. Write the Hazen-Williams equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, CHW? iii. For constant Chw, if the discharge is doubled, by what factor does the head loss increase? Part C i. Write the Manning equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for Manning's n, with units? iii. For constant n, if the discharge is doubled, by what factor does the head loss increase?
(Multiple pipes) The three tanks shown in the figure below are connected by pipes with friction factors of 0.03 for each pipe. Determine the water velocity in each pipe. Neglect minor losses. Elevation = 857 ft Elevation = 822 ft D = 1.1 ft D = 1.0 ft l = 700 ft l = 800 ft (1) (A) V₁ = i (B) V₂ = i (C) V3 = i (3) D = 1.2 ft € = 600 ft (2) ft/s ft/s ft/s Elevation = 793 ft
Q1) Mott recommends the following formula for the friction head loss hf, for flow through a pipe of length L and diameter D : where Q is the volume flow rate , A is the pipe cross-section area , and Ch is a dimensionless coefficient . Determine the dimensions of hf? hf = LG *0.551. A. Ch. Do.63)1.85
determine the flow rate at pipe 1 and pipe 2 and pipe 3.please show your complete solution.
Consider flow in a 350mm diameter steel that is coated with a very smooth enamel. Water flows in it with a velocity of 3.56 m/s. Determine the head loss per 160 m. a.) The Darcy Weisbach equation, b.) The manning equation c.) The Hazen William equation.
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
i)Calculate the flow rate through the system.
Water flows through the branching pipe shown in the figure below. The flowrate at section (1) is Q₁ = 1.1 m³/s, and the velocity at section (2) is V₂ = 17 m/s. A₁ = 0.1 m² P1 = 300 kPa 21 = 0 P3 = -147.2 A3 = 0.035 m² Z3 = 10 m (1) (2) If viscous effects are negligible, determine the pressure at section (2) and the pressure at section (3). P2 = i 315.3 kPa kPa (3) A₂ = 0.03 m² 22 = 0
1. Determine the flow rate at pipe 1 2. Determine the flow rate at pipe 2 3. Determine the flow rate at pipe 3
Oil (µ = 0.35 Pa-sec) flows through a horizontal 20 cm diameter circular pipe. The velocity at any point in the pipe’s cross-section a distance at a distance y from the center is: V =64(r² − y²) / μ where: r = 10 cm (radius of the pipe) Determine the following: a) Maximum flow velocity (m/sec) b) Shear stress (Pa) at the pipe’s centerline c) Shear stress (Pa) at the pipewalls?
Please explain step by step