Determine the head loss per km length of a steel pipegalvanized, with a 45cm diameter circular section. The fluid is oil. Kinematic viscosity= 1.06 x 10-5 m²/s. Flow = 190 L/s. Galvanized steel roughness = 0.016 cm. Moody Diagram0.10.090.08Transition Region0.050.040.030.070.060.050.020.0150.040.010.030.005Laminar Flow0.0020.020.001MaterialE (mm)5x10-0.0152x10Concrete, coarveConcrete, new smooth0.25Complete turbulence10-4Drawn tubingGlass Plastic PerpesIron, castSewenoldSteel, mortar linedSteel, nestedSteel, strctural or forged 0.025Water mains, old0.00250.00250.153.00.15x100.010.510-5Friction Factor = AP5x10-610-6%3DSmooth Pipe111110eVd101010Reynolds Number, Re =1010Friction FactorRelative Pipe Roughness 5

We have to determine the value of head loss per km of the length of steel galvanized pipe.

Determine the head loss per km length of a steel pipe galvanized, with a 45cm diameter circular section. The fluid is oil. Kinematic viscosity = 1.06 x 10-5 m²/s. Flow = 190 L/s. Galvanized steel roughness = 0.016 cm.

Determine the head loss per km length of a steel pipe galvanized, with a 45cm diameter circular section. The fluid is oil. Kinematic viscosity = 1.06 x 10-5 m²/s. Flow = 190 L/s. Galvanized steel roughness = 0.016 cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q3) Water at 4°C enters a tank of diameter D₁ = 50 cm at a constant mass flow rate of min= 1kg/s. An…

Q: A pipe 0.9 m in diameter and 15 km long transmits water with a velocity of 1.2 m/s. Calculate the…

A: To Determine Head Loss using Darcy weisbach formula

Q: Two chambers with the same fluid at their base are separated by a 30-cm-diameter piston whose weight…

Q: Water (P =1000 kg/m , p=1.59x108 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth…

A: i. Given data-

Q: Question 5 Water flows through a pipeline whose diameter varies from 20 cm to 10 cm in a length of…

Q: 1.) convert a pressure head of 15 m of water to meters of oil (sp. gr. =0.75). 2.) Convert a…

Q: Referring to the figure above, estimate the equivalent hydraulic conductivity for flow in the…

Q: Water from a reservoir is raised in a vertical tube of internal diameter D = 45 cm under the…

A: the atmospheric pressure, Patm=96KPa.The diameter of tube, D =45cm =0.45m

Q: A small drop of water at 20°C is in contact with the air and has diameter 0.2 mm. What is the excess…

A: GIVEN Small drop of water Temperature = 20°C Diameter, d = 0.2 mm = 0.0002 m To Determine Excess…

Q: Determine the diameter of a cast iron pipe which is required to carry water at 10 degrees C at the…

A: We have to determine the diameter of a cast iron pipe which is required to carry water at 10 degrees…

Q: The discharge through a 75-mm diameter orifice at the bottom af a large tank was measured be 1.734…

A: Given data Actual Discharge Diameter Head

Q: Q3) SAE 10W oil at 20°C flows through a straight horizontal pipe. The pressure gradient is a…

A: For laminar flow pressure drop, ∆p =P2 – P1 = (8μL Vavg)/R2 So, Vavg = (∆p R2)/8μL Where Vavg =…

Q: Three pipes of different lengths and diameters connected in series, discharges 160 liters per…

Q: A closed tank of 2 m3is filled with a fluid of 4180 kg whose kinematicviscosity is 4x10-4m2/s. Find…

Q: A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter reduces to…

A: Given : dia of duct = 0.8 m reduced dia of duct = 0.74m To Find : The velocity of flow in reduced…

Q: A right circular cylindrical tank container, 2 meters in diameter and 4 meters high, is ½ full of…

Q: Problem 6.34 A nozzle of diameter 20 mm is fitted to a pipe of diameter 40 mm. Find the force…

Q: Oil of sp. gr. 0.84 is flowing in a pipe under the conditions shown in the figure. If the total head…

Q: A 1.25 cm diameter orifice, in a vertical wall of a tank under a constant head of 5.5 m discharged…

Q: 1. Calculate the water pressure acting on the vertical walls of a concrete structure. P Ly1=5 M…

Q: Driven by pressurized air in a tank, water flows through pipes (L₁ = 40 m, L2 = 80 m, L3 = 20 m) of…

Q: If the orifice diameter is 1 cm and it is a vertical cylindrical tank of height 2 m and radius 1 m…

A: Given data, Diameter of orifice = 1 cm Height of cylinder = 2 m Radius of cylinder = 1m To find out…

Q: A cylindrical tank having a diameter of 5 m. and 8 m high is full of water. There is an orifice at…

A: Given:- d=5m h=8m Cd=0.60 area=0.02m2 To find:- time

Q: PROBLEM 40 : An orifice 30 mm diameter is located at the vertical side of a tank having water 1 m…

A: As per our guidelines we are supposed to answer only first question. Kindly repost other questions…

Q: Water at 4°C enters a tank of diameter DT = 50.5 cm at a constant mass flow rate of min= 1.1 kg/s.…

Q: The water system in a suburban area consists of an old 200-mm pipeline 760 m long which conveys…

Q: A fire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X= 0)…

A: a) Using Bernoulli’s equation, Here, the pressure is atmospheric so the pressure p1 and p2 are…

Q: The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be…

A: The given data is: Q=SN/100=0.21 m3/s λ=SN/1000=0.021 L=SN*100=2100 m

Q: Calculate the discharge through a pipe of diame ter 200 mm when the difference of pressure head…

A: Given: Diameter of pipe, d = 200 mm = 0.2 m Length, L = 500 m Pressure head difference, hf = 4 m…

Q: Q.13 Figure shows a lawn 40 cm sprinkier with unequal arms. The jets issuing out of the sprinkler…

Q: Estimate the height to which water will rise or fall in a capillary tube of diameter 3 mm. Use ? =…

A: Capillary tube of diameter = d = 3mm Surface tension = T = .0728 Nm Density of the water = ρ =…

Q: Problem 1: Water at 60°C flows at a rate of 0.015 m³/s from the reservoir through the pipe system…

A: To Determine 1. If flow is laminar or turbulent inside the pipe 2. The energy loss, b, due to…

Q: What is the head loss in pipe due to friction over the length of 30 km, if the diameter of pipe is…

A: Given data: Length, L = 30 km = 30×103 m Diameter, d = 80 cm =0.8 m Velocity, v = 30 cm/s = 0.3 m/s…

Q: A certain part of cast iron piping of a water distribution system involves a parallel section. Both…

A: We have to determine the flow rate through pipe B by assuming the flow is fully rough, thus the…

Q: Air flows steadily along a streamline from point (1) to point (2) with negligible viscous effects.…

A: condition At point 2: at point 2 velocity of floe is zero so point 2 is situated in a large area…

Q: Two pipes 1 and 2 having the same length and diameter are in parallel. If the flow in pipe 1 is 750…

Q: Refer to the given figure. Given: a = 42cm, b= 15cm, and c= 34cm Water a C 40 cm Gate Unknown liquid…

Q: Question: A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter…

Q: A Venturi meter having a throat diameter of 150 mm is installed in a horizontal 300-mm-diameter…

Q: Water flows steadly from the large open tank shown below. if viscous effects are negigble, determine…

A: We know velocity from tank filled with water is given byv=2gz1-z2so,z1-z2=4m

Q: Two pipes, each 300 m long are connected in series. The flow of water through the pipe is 150 liters…

A: CALCULATIONS OF DIA OF ANOTHER PIPE CONNECTION IN SERIES IN PIPE FLOW

Q: 8) Estimate the height to which water will rise in a capillary tube of diameter 3mm. Use o =0.0728…

Q: A fluid flows through a 100 m long and 120 mm diameter tube. In 2 minutes 0.15m3 of fluid passes…

Q: Determine the diameter of an orifice that permits a tank of horizontal cross- section 1.5m2 to have…

A: We will apply formula for volume in time dt,

Q: Figure P8.19 shows a pipeline through which water flows at a rate of 0.06 m3/s. The pipe is 3000 m…

A: The given figure is shown below:

Q: Let, length of pipe = 120 m and its diameter is 0.3 m. if head loss due to friction is 5.2 meters…

A: The given data is: Length of pipe (L) =120 m Diameter of pipe (D) = 0.3 m Head loss due to friction…

Q: Consider a fully developed laminar flow of a fluid through a 8027 m long and 4 cm diamete horizontal…

A: length, l = 8027m diameter, d = 4 cm Pressure, P= 1252 kg/m3 i) Velocity profile given, U = 61-rR2…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Moody Diagram
0.1
0.09
0.08
Transition Region
0.05
0.04
0.03
0.07
0.06
0.05
0.02
0.015
0.04
0.01
0.03
0.005
Laminar Flow
0.002
0.02
0.001
Material
E (mm)
5x10-
0.015
2x10
Concrete, coarve
Concrete, new smooth
0.25
Complete turbulence
10-4
Drawn tubing
Glass Plastic Perpes
Iron, cast
Sewenold
Steel, mortar lined
Steel, nested
Steel, strctural or forged 0.025
Water mains, old
0.0025
0.0025
0.15
3.0
0.1
5x10
0.01
0.5
10-5
Friction Factor = AP
5x10-6
10-6
%3D
Smooth Pipe
1111
10
eVd
10
10
10
Reynolds Number, Re =
10
10
Friction Factor
Relative Pipe Roughness 5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5:51 B ← 1:52 PM Correct 1/1 Points 19 36 45 The degrees of indeterminacy of the given structure is 58 60 Structural Theory (CETHOS30) - Qu... : ||| ( 28 ا ا " Aa 4G+ 0 < ●●●
2:27 O +491 .. 43% 277592989 2546007... ACTIVITY NO, I The five coplanar forces uhown in tigure below act on an the ir resulfant. object. Find K16.ON 19.0N I-ON 24.ON . An dajact otarts from rest with a conctant acceleration of a.0* abng straight line. Find a) the speed at the end of 5.00s, b) the auerage speed for the sosnterval, and c) the dietance traveled in the 5.00s. ||
Critical duration ? . 22 P 15 days 18 days O 16 days 17 days ( 3 R 4 S3 H5 U 3 > W 3 2 X 2
oil 3 сm 9 cm 6.4 cm water www Temperature Density Dynamic Kinematic Surface Vapor Viscosity Viscosity Tension Pressure °C Kg/m3 Ns /m? m?/s N/m N/m? abs. 999.9 1.792x10-3 1.792x10-6 0.0762 610 1000 1.519x10-3 1.51x10-6 0.0754 872 10 999.7 1.308x10-3 1.308x10-6 0.0748 1130 15 999.1 1.14x10-3 1.141x10-5 0.0741 1600 20 998.2 1.005x10-3 1.007x10-6 0.0736 2340 30 995.7 8.01x10-4 8.04x10-7 0.0718 4240 40 992.2 6.56x10-4 6.61x10-7 0.0701 7380 50 988.1 5.49x10-4 5.56x10-7 0.0682 12,300 60 983.2 4.69x10-4 4.77x10-7 0.0668 19,900 70 977.8 4.09x10-4 4.15x10-7 0.0650 31,200 80 971.8 3.57x10-4 3.67x10-7 0.0630 47,300 90 965.3 3.17x10-4 3.28x10-7 0.0612 70,100 100 958.4 2.84x10-4 2.96x10-7 0.0594 101,300 Given: The temperature of the distilled water is taken to be 26° C. Use interpolation in getting the density of water. Solve: Compute the specific gravity of oil based on the experiment.
5. Water at 15°C (p = 999.1 kg/m³ and µ = 1.138 × 10¯³ kg/m-s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. Assume the entrance effects are negligible, and thus the flow is fully developed. Take the roughness of stainless steel as 0.002 mm. 10 L/s 30 m 6 cm
5:26:32 0 200 vo 4G KB/S LTE il (42 expert.chegg.com/expertqna 10 = Chegg Time remaining: 01:58:15 Civil Engineering Determine the viscosity of fluid between shaft f 2- sleeve shown in fiqure below. Assume linear velocity distri bution. 200 mm flaid Aus. : I.183 pa.s V=o.2 89N Const. velaity 7 Sum dia. 0.075mn Submit Skip > |||
STA BM12 TP10 TP11 BM13 TP12 BM14 BS 5.741 1.649 НІ 72.599 FS 7.350 3.605 7.681 ELEV 64.622 70.034 61.105 62.781 64.737
%Vo lI. N e 17:19 团 / Find the equivalent force and its location او جد القوه ونقطه تأثير 1 w=2KN/m 4m 6KN/m 2 2m 4m 3KN/m 1m -4m 4 w=6KN/m R 3m 3m II
Q2/ Find all the reaction ABCDEF? 30KN 10kN/m 20 kN/m 20kN/m Fx DX 1.5m 2m 2m 1m 3m
Engineering MechanicsDetermine the friction force between the block and the surface after P was gradually increased from 0 to 200 N. In which phase will the block be classified (Phase 1 -no motion, Phase 2 -impending motion, or Phase 3 -in motion)? Choose from the choices below
Ineed Q 2
Engineering MechanicsDetermine the friction force between the block and the surface after P was gradually increased from 0 to 200 N. In which phase will the block be classified (Phase 1 -no motion, Phase 2 -impending motion, or Phase 3 -in motion)?