The equivalent capacitance at terminals a-b in the circuit is 30 µF. Calculate the value of C. Take C₁ = 70 μF. b 14 μF The value of Cis UF.
Q: Consider the circuit below. You may assume it has reached steady state. The phasor diagram shows the…
A:
Q: 6. Find v(0*). a) -5 V b) 10 V c) -15 V d) 20 V e) none of these 7 Find (E) 10 V 2 kn ww t=0 20 mH…
A: Since you have asked multiple questions in a single request, we will be answering only the 1st…
Q: The parameters of the ramp generator in Fig. 16.53(a) are R = 10 kn, Vcc= 15 V, VBE = 0.7 V, and a…
A: Given Ramp generator R=10 kΩ Vcc =15 V VBE =0.7 V βF =100 f0 =Free running frequency
Q: The phase angle between 15sin(7t) and 10sin(7t+50°)
A:
Q: Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2…
A:
Q: How long does it take electrons to get from a car battery to the starting motor? Assume the current…
A: We need to find out the time for given charge and current .
Q: As being an electrical engineer you could join the Institution of Electrical and Electronics…
A: Yes, As being an electrical engineer we can join the Institution of Electrical and Electronics…
Q: Determine vo versus v₁ for the circuit shown in Figure 2. Assume that the MOSFET operates in…
A:
Q: A capacitor consists of two metal plates each 500 x 500 mm² and spaced 6 mm apart. The space between…
A: Given data, Constant ε0=8.85×10-12 F/m Dimensions 500×500 mm2 or 0.5×0.5 m2 Distance , d1=2 mm=0.002…
Q: Machines 3 phase generator 0.85 lagging jXs =j 12 razo Synchronous 11) 9 MVA pf V+el = 13.1 KV Fa…
A:
Q: Explain the circuit
A: The given circuit is a astable multivibrator using 555 timer and it is used to produce varying pulse…
Q: b) For the circuit shown in Figure Q2b, apply mesh analysis to solve for the voltage V₂ and the…
A: Given, The circuit diagram,
Q: 3. Assume the input to the circuit below is given by 3sin(2лft) Volts, where f-1000 Hz. What does…
A:
Q: nd ...1 - @b Wa p(t) H(jw) A+ (b) T Wa @b@
A: Given Data: p(t)=∑n=-∞+∞∂(t-nT) To Find: ωa=?ωb=? Tmax=?
Q: Determine whether the following functions can be PSD of real-valued WSS random process. a. (1+10f)…
A: C)
Q: A 36, 460 V, 100 hp, 60 Hz, six-pole induction machine operates at 3% slip (positive) at full load.…
A: Given: In this question, A three-phase 460 V , 100 hp , f=60 HZ , P=6 induction machine operates at…
Q: Ⓒ F(x, y, z) = πTM (0,3,5,6) 2 Don't care (2,7)
A: The k-map can be used to find the simplified Boolean expression for the given maxterms. The reduced…
Q: The short-circuit test is conducted to determine the series equivalent circuit parameters of a 3-…
A: Data Given is for 3-Phase, 5 MVA,66/33 kV, 50Hz, Delta/Wye connected transformer Short Circuit…
Q: A single phase, 60Hz, 200-km medium nominal-T transmission line supplies a load of 700 MW at 0.95…
A:
Q: Determine the simplified Expression Using Map Method [DON'T CARE METHOD] 1 F (A, B, C) (3 {(1,2,4,7)…
A:
Q: An RL series circuit is connected to a 240 volt 60 hz line the capacitor has current of 1.25 amperes…
A:
Q: Write the loop equations for a Buck converter in the two modes if the inductance is characterized by…
A: Buck converter We have to write loop equations in two modes i) Mode 1 : Switch is on ii) Mode 1 :…
Q: Which of the following has a sine look-up table stored in memory? ODDS chip OPLL chip O Op amp O All…
A: The sine look-up table is used by the synthesizer to generate the sinusoidal waveform and it will be…
Q: The op-amp shown in the following figure has R1 = R2 = R3 = 100 02 Rf = 1k02, and V1 = V2 = V3 = 50…
A: Given, The circuit diagram of the op-amp, The value of resistors, R1=100 ΩR2=100 ΩR3=100 ΩRf=1000 Ω…
Q: the output frequency
A:
Q: The symbol ∝ has the meaning of "is proportional to" True False
A:
Q: Recall the equation of the Z-parameters -- V₁ Z11 Z12 THE A Z21 22 Determine the Z-parameters for…
A: We need to find out the Z parameters for given circuit.
Q: B D figure 2 VA = lOV, = -3V VB VF = 12 V VH = 5V 5v find the remaining voltages
A:
Q: Explain each circuit below and describe how many seconds everytime it lights
A: Given circuits are of 555 times based astable multi-vibrator. The schematic of circuits are as shown…
Q: Design a 3-bit counter which counts in the sequence: 001, 100, 101, 111, 110, 010, 011, 001, ... (a)…
A: We need to design a 3-bit counter which counts in the sequence: 001, 100, 101, 111, 110, 010, 011,…
Q: 1) Draw a circuit below which has resistors both in series and in parallel (each of whose…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: Consider a unity feedback system with its forward transfer function G(s) = K/[s(s+3)(s²+2s+2)] where…
A: Feedback System A feedback system is one that modifies the applied input signal in order to produce…
Q: Carers 9. A pn junction is formed by: a. b. the recombination of electrons and holes ionization C.…
A:
Q: Design a circuit with logic gates that deactivate three solenoid valves when the object is present…
A: According to the question, we need to design a circuit with logic gates that deactivate three…
Q: The load in milling factory is having active and reactive power of 100 kW and 59.33 kVAr,…
A: Given Total load power Active power, Pload=100 kW Reactive power, Qload=59.33 kVAr Power factor…
Q: nsider a unity feedback system with its forward transfer function G(s) = K/[s(s+2)(s²+2s+ here K≥ 0.…
A: Since you have asked multiple questions in a single request, we will be answering only the first…
Q: 1. Find the currents and determine the voltage per node. 18Ω 30V bF 320 2502 M 14 15 15Ω 13 502 d 16…
A:
Q: 1. For the network shown below, sketch vo and iR. iR Vj 0 10 V -10 V + Vi - 1kQ 艹 Si + 1 kn Vo
A: Voltage source with 10V peak Circuit with 2 1000 ohms in series and output is taken at 2nd resistor…
Q: Calculate the number of Coulombs of charge needed for a current of 2 amps to flow for 14 minutes.
A: Given I = 2A t= 14 Minutes Need to find coulombs of charge(Q).
Q: Determine whether the following functions can be PSD of real-valued WSS random process. a. (1+10)…
A: A)
Q: 5. If a potential difference of 240 V is applied to a field winding at 15°C and the current is 4 A.…
A:
Q: Q1 using the curves of Fig. 1: a. Determine the voltage across Ge diode at a current of 2 mA. b.…
A:
Q: 1- What is meant by calling a conductor is a healthy conductor? 2- Mention below the classification…
A: Since you have posted a question with multiple sub-parts, we will provide the solution only to the…
Q: Determine Vo and is in the Op-Amp circuit shown in the figure below. ww 6 ΚΩ |12V 6 ΚΩ 16ΚΩ 6 ΚΩ 6…
A: We need to find out the output voltage and current for given circuit.
Q: 4. Given the circuit shown in Figure 3, determine (a) the total equivalent resistance, (b) the total…
A:
Q: it V-8 V. obtain expressions for ( and vc valid for all values of t. (You must provide an answer…
A: The required parameters can be obtained by analysing the state of the circuit before and after t=0.…
Q: a. Sketch the output v. and determine the dc level of the output for the network of Fig. 1. Repeat…
A: We need to find out the output voltage for given circuit .
Q: VDD = 3.6 V and RL = 8.5 kn, please answer the following questions. Note that M₁ and M₂ have the…
A:
Q: QA) a. Sketch the output v. and determine the dc level of the output for the network of Fig. 1. b.…
A:
Q: Note that VA (early voltage) →∞. Note also that C1 and C2 are large AC coupling capacitors. (Hint:…
A: The given circuit is as shown below,
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
- Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
- An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
- A 100uf capacitor and a3.6kohm are connected in series. How long will it take for the capacitor to change its charge completely?A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 msAn inductor of 230 milli Henry, a capacitor of 15 micro farad and a 200 ohm resistor are in series across a 36 V and 60 Hz voltage source. Find the total current a. 150 mA b. 0.164 A c. 0.2 A d. 170 mA