The direction of the forces in the cut members in a free body diagram of a plane truss used in the Method of Sections is: O Impossible to determine. Perpendicular to the direction of the member. O Always along the axis of the cut member and in tension. O Always along the axis of the cut member and in either tension or compression.

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: What is the magnitude of the resultant force related to the following distributed load.

A:

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: 2. EVALUATE dx e

A: The indefinite integration is represented by ∫f(x)dx and the solution is F(x)+C, where F(x) is…

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: find Q ? L 7om dsolm Lsioum L. 2om f=0002

A: Velocity of flow at entry of 100 m pipe, v=2gh where, h=height of reservoir=8m Therefore velocity,…

Q: What is the magnitude of the resultant force related to the following distributed load. 15 kN/m 7…

A: Option D is correct.  Resultant of uniformly distributed load is 99 kN.

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: The lower half of the moulding box is O a. Raiser O b. Drag O . Runner O d. cope

A: Given data Lower half of the moulding box is

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: Find (Ix&ly), if a=30mm. a

A:

Q: A) Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A:

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: Move the forces in the shape to point a

A:

Q: 5. The rectangular components of force are respectively. 220° 100 N (a) -100 sin 220°, –100 cos 220°…

A: As we know, there are four quadrants: I, II, III, IV. In the first quadrant, x and y-axis are…

Q: is the moment clockwise or counterclockwise?

A: Moment about point O is given by, C→MO=28.282 i^-19.148j^-5.13k^ The direction of moment is shown in…

Q: //// // R R J3 Js Jy J. J8 R lt)

A: given; mass of block=mweight of block(w)=mgforce=F

Q: 2. The size of 1/2 in. would refer to the with regard to ACR copper tubing.

A: The correct option is (b)  Outer Diameter (OD)

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.