A solid cantilevered aluminum alloy rod, 10-mm in diameter, supports a Parol (Christmas Lantern). The hanging Parol subjects the rod to a bending moment of 10.2 Nm along the x-axis, as well as Torque (T) at its fixed end (Section B). If the yield strength oYield in tension of the aluminum alloy is 103.9 MPa at point n of Section B, what is the maximum torque the rod can carry under the maximum distortion-energy theory (MDET)? L aluminum rod Figure 1A Y B cross-section of the rod Figure 1B Image is from Parol clipart 2 Clipart Station

A solid cantilevered aluminum alloy rod, 10-mm in diameter, supports a Parol (Christmas Lantern). The hanging Parol subjects the rod to a bending moment of 10.2 Nm along the x-axis, as well as Torque (T) at its fixed end (Section B). If the yield strength oYield in tension of the aluminum alloy is 103.9 MPa at point n of Section B, what is the maximum torque the rod can carry under the maximum distortion-energy theory (MDET)? L aluminum rod Figure 1A Y B cross-section of the rod Figure 1B Image is from Parol clipart 2 Clipart Station

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.17P: .17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the...

See similar textbooks

Similar questions

Repeat Problem 2.3-18, but assume that the bar is made of aluminum alloy. If P2= 200 kN, what is P1so that displacement
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
Repeat Problem 2.4-8, but assume that the bar is made of aluminum alloy and that BC is prismatic. Assume that P = 20 kim. L = 3 ft.t = 314 in., b1 2m.b 2.Sin.andElO.400ksi.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
2. The tapered cylindrical bar in Fig. 2 is subjected to opposing torques T on its free ends. For the tapered section only, the angle of twist 0 can be expressed as: 32 TI(d? + d,d2 + dž) Gd d? 37n (a) Derive an expression for the effective spring constant keff for the entire bar, treating each segment as a torsional spring in series. Fig. 2 (b) For the bar shown, let; I, = 12 = 12 in., 1= 24 in., d1= 0.25 in., d2= 1 in., T = 1000 lbf-in., and G = 13.5 x 103 kpsi. Calculate the angle twist 0 for the entire bar using the expression for kef determined in (a). Verify that this value is the sum the angles of twist for each individual %3D %3D segment.
For the indicated part. What would be the maximum torque that can be applied to the indicated part if the bar is solid, made of steel, with a diameter of 5 cm, L = 2m and the total angle of torsion in the length cannot exceed 2 degrees? Assume G = 80 GPa. (Hint: Twist angle has to be in radians to use in formula)
3 An aluminum (shear modulus = 2.8× 1010 Pa) rod is 25 mm in diameter and 50 cm long. One end is rigidly fixed to a support. What torque must be applied to twist the rod 4.5° about its longitudinal axis?
TEST YOUR UNDERSTANDING! Problem 1 Four wires support the rigid members CD and AB. If a 500-lb load is applied at point I, determine the angle of tilt of AB and the displacement of point A. The members were originally horizontal, each wire has a cross-sectional area of 0.5 in² and E = 29 x 106 psi. (Taken from Hibbeler, 2015) Follow these questions for your solution: 1. Draw the FBDs of bar CD and bar AB. What are the forces in the wires? Problem 2 The horizontal rigid bar is supported by bars A and B and a pin support. If the system is loaded by P₁ and P2, what would be the vertical displacement of the point of application of P₁? Follow these questions for your solution: 1) Draw the FBDs needed. What is the normal force in bar A? in bar B? 2) Draw the deformation diagram. What compatibility equation would you use to determine the displacement of the point of application of P₁? How did the horizontal bar tilt? Answer to Test your understanding box 1 Problem 1: E Problem 2: D THA 1.8 ft…
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Angle of Twist in degrees?
A hollow circular shaft of inner radius 20 mm, outer radius 40 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, Calculate the torsional stiffness of the shaft (in kN-m/rad) is
B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;