The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D Rod Нead b Answer: Pmax" kN

Q: The shaft shown in the figure left has the diameters 304 Stainless steel - 2014-T6 Aluminum and…

A:

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.500 in., and each side…

A:

Q: in the figure. Also, determine the factor of safety for the tank based on Von-Misses and Tresca…

A:

Q: The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy…

A:

Q: he rigid bar AB with a length of 5m, is attached to two vertical rods and is horizontal before the…

A: Given

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: The structure shown has a diameter of 40??. The length dimensions are ? = 525 ?? and ? = 110 ??.…

A: To find: The stress state at point H. Given: The diameter is D=40 mm. The dimension are a=525 mm and…

Q: - 25 mm Q: The steel column of circular cross section is attached to rigid supports at A and C.…

A:

Q: Problem 3 The two solid circular rods with a 6.6x10*/F are in an initial stress-free state at a…

A:

Q: Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from…

A:

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

A:

Q: The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is…

A: Diameter of pin, d=24 mmWidth of the bar, w=80 mmThickness of the bar, t=20 mmDimensions of each…

Q: A bent rod has a diameter of %3D15 mm and is subjected to a force of P= 600 N. What is the normal…

A: Given ,  d= 15 mm  P = 600 N

Q: 30 30 The cotter shown in the figure is used to fix the squared spigot rod to the plate. The rod is…

A: Given: The diameter of rod, d = 28 mm The yield strength of cotter and the rod, Sy = 280 MPa The…

Q: Neglecting the weight of the bar as shown in the figure, determine the stress in each rod if the…

A:

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A:

Q: The links of the chains are made of steel that has a working stress of 300 MPa in tension. If the…

A:

Q: The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. T column is…

A:

Q: The elastic portion of the stress- strain diagram for the 2014-T6 aluminum is shown in the figure. A…

A:

Q: The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear…

A:

Q: circular tube AB is fixed at one end andfree at the other end. The tube is subjected to axialforce…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data: P=64 kips diameter of bolt (d)= 0.75 in.

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P =…

A: Find the compressive stress of the column. Find bearing stress of the concrete. Find the punching…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume…

A: Diameter d = 14 mm.Length L = 0.9 mAngle Area is given by,

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A:

Q: Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid…

A: Given data:   Find: Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is…

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: Determine the load that can be applied at the end of the rigid bar if the stress in either spring…

A:

Q: Two 6061-T6 aluminum tubular rods AB and BC are welded at B and loaded as shown in the figure (P =…

A:

Q: 200 mm A P 200 mm B 1 P 600 mm 400 mm

A: Write the given values with suitable variables. τmax=45 MPa=45×106 Pado=50 mm=0.05 mdi=40 mm=0.04 m…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A: In possion's ratio always consider change in diameter without concerning the sign only take…

Q: A 2-meter concrete column (Ec=30 GPa) is reinforced with six 25-mm diameter steel bars (Es=200 GPa)…

A:

Q: OF = 5712 N

A: Calculate linear strain with the given data

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: ions of the cross section of the leading edge and torsion box of an airplane wing ted as shown. If…

A:

Q: The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a…

A:

Q: A suspension system of a mountain bike is held by a pin at point C and supported by a shock absorber…

A: Both pins are experiencing double shear and bearing pressure stress.

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at end A as…

A:

Q: The tube has an inner diameter d; = 20 mm and an outer diameter d, = 22 mm. It is subjected to an…

A: In strength of material , Properties and failure of material is analyzed. Material is failed due to…

Q: The circular column is subjected to a compressive force of 5kN if the stress in the column is…

A: