The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank Support bracket 8 F₁ a B b

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank Support bracket 8 F₁ a B b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The assembly consists of three disks A, B, and C that are used to support the load of P. The load P (kN)=328. The thickness of block B t1(mm)=26. The thickness of block C t2(mm)=13. The allowable bearing stress (allow)b (MPa)=213. The allowable shear stress Tallow (MPa)=71 B - dz =Bearing area of disk A 0.00559 0.00154 0.003 0.00433 0.00858 =Bearing area of disk B 0.00154 0.00766 0.00929 0.00259 0.00581
The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear stress in the bolts must be limited to 185 MPa, determine the minimum bolt diameter that may be used in the connection. P 24.3 mm O 18.5 mm O 22.6 mm 29.3 mm O 14.0 mm
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 290mm, b = 170mm, c = 70mm, and 0 = 35°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 37 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket Answers: Tpin 8 = i Bell crank i a B MPa MPa F₂
Current Attempt in Progress The five-bolt connection must support an applied load of P = 4300 lb. If the average shear stress in the bolts must be limited to 43 ksi, determine the minimum bolt diameter that may be used for this connection. cocco Answer: dmin= i in.
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket F₁ Answers: Tpin B = i Ob = i a B MPa MPa
Attempt Histor Current Attempt in Progress The five-bolt connection shown must support an applied load of P- 500 kN. If the average shear stress in the bolts must be limited to 270 MPa, determine the minimum bolt diameter that may be used in the connection. 27.8 mm O 13.5 mm 18.1 mm O 21.7 mm O 23.1 mm
- The bell-crank mechanism is in equilibrium for an applied load of F₁ = 15 kN applied at A. Assume a = 270mm, b = 170mm, c 70mm, and 9 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 34 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket a B b
HANDWRITTEN THEN BOX THE FINAL ANSWERS
The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 26 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 120 MPa, the punching shear stress in the support plate cannot exceed 110 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Rod Answer: Pmax i Hole diameter D Head KN d a
Q3/ Two plates are riveted together have a width of 130 mm , thickness of 25 mm and the diameter of the rivet bolt is 10 mm. When it's subjected to a load of 150 KN as shown in fig.2, determine: 1- tensile stress 2-shearing stress 3-bearing stress. 10mm= 130 mm 25 mm 25 mm Fig.2
The d = 13-mm-diameter solid rod passes through a D=21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 28 mm, and the head has a thickness of t = 8 mm. If the normal stress produced in the rod by load P is 150 MPa, determine (a) the bearing stress acting between the support plate and the rod head. (b) the average shear stress produced in the rod head. (c) the punching shear stress produced in the support plate by the rod head. Support Plate Hole diameter D Rod Head b Calculate the cross-sectional area of the rod. Answer: Arod mm²
0 Required information The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.1 x 106 psi for aluminum and 5.2 x 106 psi for brass. If T = 16 kip in, a-1.1 in. and b=2.2 in., determine (a) The reaction torque at A (b) Maximum shear stress in BC T 12 Assuming the reaction torque at A is TA (kip.in)(4). TA<16(kip.in) express the magnitude of (1) the internal reaction torque from A to B as TAB ([ ) (kip.in) (i) the internal reaction torque from B to C as TBC ) (kip.in) TA+ TA+