The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 20mm, dBC = 25mm, and dCD = 12mm. Take Ecu = 126GPa.

Q: Calculate the maximum shear stresses from the torsional moment it the shaft between the points B and…

A:

Q: The beam is made of southern pine for which E, = 13 GPa. Take that a = 160 mm and b = 100 mm.…

A:

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A:

Q: Direct a key d the Hub Shear plane Hub Key F2 y, or anical F1 T=Torque Shaft T=F(D/2) F = Force of…

A: Given data as per question b= 1/2in l = 2.25in h= 3/8in force = 8000lb.in shaft diameter = 2.0 in

Q: Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value…

A: d = 50 mm G = 85 Gpa T3=500 N.m

Q: d Bronze B Steel - b–

A:

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: The shaft consists of a 3-in.-diameter aluminum segment that is rigidly joined to a 2-in.-diameter…

A: Given data: The diameter of the steel rod is dst=2 in The diameter of the aluminium rod is dal=3 in…

Q: A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of…

A:

Q: The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If…

A:

Q: A pulley is keyed to a shaft midway between two anti-friction bearings. The bending moment at the…

A:

Q: A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the…

A: The power P can be given by - P=90×1000=2πNT6090×1000= 2π×200×T60T=4297.18 NmThe shear stress can be…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at  end A as…

A: Given data:

Q: N in 1 in .9 y 12 in in D C B A -in

A:

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.18 mm and…

A: Given displacement of nodes 2 and 3.  Required: horizontal displacement of point P (d)

Q: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of…

A: Consider a shaft of diameter d and length L is subjected to a torque T. Then, torsional shear stress…

Q: 3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe…

A:

Q: equations of the elastic curve for the shaft using the x1 and x2 coordinates. Take El as constant…

A:

Q: Determine the vertical displacement of point B and rotation of point C using double integration…

A:

Q: find the vertical displacement at Point B of the built-in entry in the figure by Castigliano's…

A: For the given beam  E = 200 GPa I = 30*106 mm4   To determine  vertical displacement at point B by…

Q: Determine torsional stiffness of the shaft

A:

Q: The copper shaft is subjected to the axial loads shown in the figure. Determine the displacement of…

A: Here, P is the applied load at end A and is the area of section AB.Determine the cross-section area…

Q: A shaft used in an aircraft engine is 50 mm diameter, the maximum allowable shear stress is 84…

A:

Q: Finding the value of sectional modulus of shaft having diameter 3 m

A: Given data : Diameter of shaft is given in this question . With help of this data we have to find…

Q: 2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as…

A:

Q: The shaft shown consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in…

A: Given   Diameter aluminum, da = 3 in            Diameter steel, ds = 2 in…

Q: The cross section of the rim of an iron flywheel (S+3)ft. In diameter is a rectangle 12" by 3". How…

A: A flywheel is a spinning device that is designed to efficiently store rotational energy by using…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: The solid shaft is made of an elastic-perfectly plastic material as shown in Figure 5. Determine the…

A: The torque is expressed as,

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: Determine the maximum allowable torque T that may be applied.

A:

Q: A 75 mm Bronze a B 50 mm T Steel -b- DC

A:

Q: Calculate the normal stress and the shear Stress at Points C and D The shaft is hollow; inner and…

A: shear stress at points C and D for a hollow shaft subjected to axial force (N), bending moment (M),…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings T = 15 kN.m and…

A:

Q: Design the shaft (Find the diameter d). T = 2kNm; T = 3kNm; L = Im; Tall = 58MP..

A: Given data: Allowable shear stress, τall = 58 MPa. The magnitude of torque T1, T1 = 2 kN·m. The…

Q: A solid shaft has a diameter of 40 mm and length of 1 m. It is made from an elastic-plastic material…

A: To find the maximum elastic torque Ty=? Using Torsional equation Ty=τYJR…

Q: Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it…

A:

Q: Task 4: A solid steel shaft in a rolling mill transmits 20 KW of power at 2 Hz. Determine the…

A: The steel shaft of the rolling mill transmits 20KW at 2 Hz, The torque in the shaft while…

Q: The solid steel shaft has a diameter of 35 mm. Determine the absolute maximum shear stress in the…

A:

Q: find the displacements at the inner radius of a long cylinder of inside diameter 80mm and outside…

A:

Q: A shaft 80 mm diameter transmits the power at maximum shear stress of 63MPa. Find the length of a…

A: Given details: d=80 mmζmax=63 MPawkey=20 mmζkey=42 MPa Formula used:…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.