Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m 0.5 m 120 mm T = 10 kN.m i В TR = 20 KN.m 1 D Tc = 30 KN.m Tp = 6 kN - m Figure Question1

Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m 0.5 m 120 mm T = 10 kN.m i В TR = 20 KN.m 1 D Tc = 30 KN.m Tp = 6 kN - m Figure Question1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
FIl-1. Determine the minimum dimension a to the nearest FII-4. Determine the minimum dimension h to the nearest mm of the beam's cross section to safely support the load. The wood has an allowable normal stress of atow- 10 MPa and an allowable shear stress of Talow -1 MPa. in. of the beam's cross section to safely support the koad. The wood has an allowable normal stress of ale 2 ksi and an allowable shear stress of Tatow - 200 psi. 1.5 kip/ft 6kN 6kN 2a FIl-1 FII-4 FIl-2. Determine the minimum diameter d to the nearest in. of the rod to safely support the load. The rod is made of a material having an allowable normal stress of o- 20 ksi and an allowable shear stress of rh - 10 ksi. F1l-5. Determine the minimum dimension b to the nearest mm of the beam's cross section to safely support the load. The wood has an allowable normal stress of oow- 12 MPa and an allowable shear stress of Tlow - 1.5 MPa. 3 kip ft 50 kN 5 kN-m 5 kN-m -15 ft -1.5 ft 3kip m- -1 m FII-2 FIl-3. Determine the…
A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa..Power (P) 22 in kW , Speed (N) 550 in Rpm
PROBLEM: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of the gear is 1 kN. If the allowable shear stress is 45 MPa, determine the shaft diameter. FIGURE: Bearing 150 mm 100 mm. 200 mm. Gear Shaft 100 mm Bearing SOLUTION: Instructions: Solve the diameter of the shaft. To add an equation in Word, select Insert > Equation or press Alt + = Example: = F A
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa. Meanwhile, determine the maximum mean diameter of a taper for use to fix a lever to a shaft. If it transmit a maximum torque f 750 in-lb . The shaft diameter is in 3in
Determine the torsion on the rigid supports and the maximum shearing stress developed in each segment. Provide a torque diagram, strictlv follow instructed sign convention, and start from left to right. Use 2 decimal places. A 0.5 in. B 5 in. C 500 lb-ft 8 in. 1 in. D 12 in.