The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque To that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. 1.30 in. 0.60 in. 5.0 in. To 14.5 in B

The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque To that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. 1.30 in. 0.60 in. 5.0 in. To 14.5 in B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid 32 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 1000 N, LAB = 600 mm, LBC = 800 mm, LCD = 800 mm.
The solid 36 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 800 N, LAB = 600 mm, LBC = 850 mm, LCD = 850 mm.
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B
A solid circular bar ABCD with fixed supports is acted upon by torques T, and 2T, at the locations shown in the figure. 270 D 4L 10 (a) Obtain a formula for the maximum angle of twist o ay of the bar. (Enter the magnitude. Use the following as necessary: G for the shear modulus of elasticity, I, for the polar moment of inertia, where p is lowercase, L, and To.) Pmax = (b) What is if the applied torque T, at B is reversed in direction? (Enter the magnitude. Use the following as necessary: G for the shear modulus of elasticity, I, for the polar moment of inertia, where p is lowercase, L, and To:) Pmax Ymax =
The solid 20 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 900 N, LAB = 750 mm, LBC = 1200 mm, LcD = 1200 mm. A B C D P Answer: (a) VA = (b) vc= LAB LBC mm mm Q LCD
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11800 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 2900 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 92 in., b = 40 in., and c = 34 in.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.
T4
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.