I need the answer as soon as possible The coefficient of compressibility is the ratio ofA. Change in void ratio to change in effective stressB. Volumetric strain to change in effective stressC. Charge in thickness to change in effective stressD. Stress to strain

Coefficient of compressibility is defined as the ratio of Change in void ratio to change in…

Answered: The coefficient of compressibility is…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

The value of stress concentration factor depends on the geometry. If Ka and Kb are stress concentration factor for case (a) and case (b), respectively, which answer of the following is true? Ka > Kb KA = KB KA < KB None of the rest.
2. For the state of stress shown, determine the range of value of for which the normal is equal to or less than 100 MPa and 50 MPa. stress x' + 90 MPa 60 MPa =
A state of stress is specified in the figure shown. Determine the principal stress oy (mPa) if P =-20 mPa and y = 15 mPa P V
The stress which acts in a direction perpendicular to the area is called O a. Strain Stress O b. Thermal stress O c. Normal stress O d. Shear stress
A state of stress is specified in the figure shown. Determine the principal stress oy (mPa) if P =-27 mPa and v = 20 mPa P
. Which of the following is known as the unequal stress? Select one: a. Differential Stress b. Hydrostatic Stress c. Lithostatic Stress
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 41 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11 mm. The maximum stress developed in the flat plate is 235 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ii) Nominal Stress in MPa iii) Diameter of the hole (d) in mm Hole with stress concentration factor 2 35 mm W2 35 mm P 300 mm 350 mm- 250 mm
Determine the effective stress (i.e. grain pressure) σ'v0 acting in the plane of consideration
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 44 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11.5 mm. The maximum stress developed in the flat plate is 228 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ( ii) Nominal Stress in MPa ( iii) Diameter of the hole (d) in mm
Q. No .3 On the free surface of an aluminum [E = 10,000 ksi; v = 0.33] component, the strain rosette shown in the figure was used to obtain the following normal strain data: = -500 µɛ, E = -220 µe, and &e = +600 µɛ. Determine the normal stress that acts along an axis that is rotated at an angle of 0= 45° coun- terclockwise from the positive x axis. 60 60 60
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.
Strength For the state of plane stress shown, determine the largest value of o, for which the maximum in plane shear stress is equal to or less than 75 MPa. After you determine the value, draw Mohr circle for the case

SEE MORE QUESTIONS

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The coefficient of compressibility is the ratio of A. Change in void ratio to change in effective stress B. Volumetric strain to change in effective stress C. Charge in thickness to change in effective stress D. Stress to strain