The circular rods AB and BC is joined at B and fixed at the wall at A, as shown in the figure. Before the load P is applied at B there is a gap between the rods and the wall. LAB =3700 mm, dAB = 26 mm, EAB = 235 GPa, δgap = 10 mm LBC =5700 mm, dBC = 24 mm, EBC = 172 GPa, and P = 75 kN Determine the normal force in BC. Determine the normal stress in BC.

The circular rods AB and BC is joined at B and fixed at the wall at A, as shown in the figure. Before the load P is applied at B there is a gap between the rods and the wall. LAB =3700 mm, dAB = 26 mm, EAB = 235 GPa, δgap = 10 mm LBC =5700 mm, dBC = 24 mm, EBC = 172 GPa, and P = 75 kN Determine the normal force in BC. Determine the normal stress in BC.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

) The Surface tension of water in contact with air at 23°C is given as 745x10-4 N/m. The pressure inside a droplet of water is to be 0.017 N/cm2 greater than the outside pressure, calculate the diameter of a droplet of water in mms (ii) The Surface tension of water in contact with air at 23°C is given as 780x10-4 N/m. The pressure inside a soap bubble is to be 0.017 N/cm2 greater than the outside pressure, calculate the radius of it in mm. on (ENTER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) SOLUTIONS: ) The diameter of the water droplet in mm = (ii) The radius of the soap bubble in mm =
2.25. A solid cylindrical bar of diameter D is subjected to a bending moment M and a torque T. Use equations (1.17, 1.18) to find the corresponding stresses and hence obtain an expression for the equivalent tensile stress OE according to von Mises' theory.
Nanotechnology, the field of building ultrasmall structures one atom at a time, has progressed in recent years. One potential application of nanotechnology is the construction of artificial cells. The simplest cells would probably mimic red blood cells, the body’s oxygen transporters. Nanocontainers, perhaps constructed of carbon, could be pumped full of oxygen and injected into a person’s bloodstream. If the person needed additional oxygen—due to a heart attack or for the purpose of space travel, for example—these containers could slowly release oxygen into the blood, allowing tissues that would otherwise die to remain alive. Suppose that the nanocontainers were cubic and had an edge length of 25 nanometers. What is the volume of one nanocontainer? (Ignore the thickness of the nanocontainer’s wall.)
Nanotechnology, the field of building ultrasmall structures one atom at a time, has progressed in recent years. One potential application of nanotechnology is the construction of artificial cells. The simplest cells would probably mimic red blood cells, the body’s oxygen transporters. Nanocontainers, perhaps constructed of carbon, could be pumped full of oxygen and injected into a person’s bloodstream. If the person needed additional oxygen—due to a heart attack or for the purpose of space travel, for example—these containers could slowly release oxygen into the blood, allowing tissues that would otherwise die to remain alive. Suppose that the nanocontainers were cubic and had an edge length of 25 nanometers. Suppose that each nanocontainer could contain pure oxygen pressurized to a density of 85 g/L. How many grams of oxygen could be contained by each nanocontainer?
How are equations 1 and 2 combined to that? Especially, where does the (n-1)/n comes from
Ascume that the vircogity of aglecs varies with tempersture according to N= Vis cosim, -A=lonstant Rzgas Coxelant and sCis = activation enegy of Viscosiny +1760k It hee a *て一 klhst is the Vis Casüly at 45ok? ना क , ८- 0्5न्द सउ्र ग
What is the differential relation between displacement, velocity and acceleration?
Please solve this question again. I think previous solution was incorrect
A 3000 N vehicle, shown in the figure, crosses a rough road at 120 km / h. The amplitude of the sine curve representing the path is 2.5 cm and the wavelength is 5 m. According to this; a) 120 km /h speed is the critical point where resonance occurs. Determine the spring constant (k) in case of velocity. b) Determine the spring constant of the spring that will give a vibration amplitude of 0.5 cm at a speed of 120 km / h.
Formül; seG2 5 için a-(1- 0,630b/a) M,(lzy.z-1y-y) + M,(1;1- ly.y) TL Gab 10 cm It _% + 4%, tan28, = + dy9: – Oy cor20 + Trysin20. dart 2ry 600 N Ty -- sin20 + Tycos20, omake.min- +r, 14 cm Tmaks + ry Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the normal stress at point A. O O MPa O 33,37 MPa O 76,39 MPa O 94,75 MPa O 48,86 MPa
Answer the folowing with True or False. Density of a foam material depends on the wall thickness and size of its foam cells. ( ) BCC structure is more densely packed than the FCC structure. ( ) The anion – cation size ratio has an important influence in determining the crystal structure of ionic solids. ( ) CFRP and GFRP are examples of hybrid materials. ( ) The density of a material is determined exclusively by its atomic weight. ( ) Body diagonal in BCC structure has Miller indices of [111]. ( ) The relationship s = Ee is known the Ohms law. ( ) A closed packed triangular plane in FCC crystal has Miller indices of (111). ( )
abaqus but I have only lame's constants to define potential function mu and lambda. I am confused with abaqus terminologies, it needs C10 and D1. After some search I found that lame constant lambda is shear modulus mu and C10 = mu/2 And lame constant mu = bulk modulus kappa, D1 = 2/kappa I am bit confused with these terminologies as haven't done such analysis before