The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D If the maximum flexural stress above the neutral axis is 100 MPa , What is the value of the uniformly distributed load when it is to be replaced by w in kN/m.

The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D If the maximum flexural stress above the neutral axis is 100 MPa , What is the value of the uniformly distributed load when it is to be replaced by w in kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.Determine the maximum compressive stress acting on the cross section. 2.Determine the maximum…

Q: 250mm P 50mm 250mm B 50mm 2 m 2 m 50mm 400 mm

Q: A rigid beam is supported by bar DE. If the vertical displacement of point D is to be less than 0.1…

A: Let FDE be the force on the bar DE.Vertical displacement at point D will be equal to the change in…

Q: aluminum bar is 2800 mm2. Compute the stress in the aluminum bar after the 400- kN load is applied.…

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: Length, L = 300 mm Force, F = 414 N Modulus of Elasticity, E = 2 x 105 N/mm2 Moment of…

Q: Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal…

Q: The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA 120 mm 2.0 m INa =…

A: A loaded beam is given with its cross section and it has been asked to determine its compressive…

Q: 50mm a biaxial load that results in B C Given: A “happy-little-cube" of material is subject O = 150…

Q: The cantilever beam, whose loading condition and cross-section are given in the figure, is ideal…

Q: 1. A T-section beam that is subjected to a concentrated and a distributed load can be identified in…

Q: A 6-m simply supported box beam is loaded as shown in the figure. Determine the maximum flexural…

Q: * For the cantilever beam shown. find the value of Torsion stress at point :C due to Torque 4 KN 6…

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

Q: A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of…

Q: Figure Q2 shows a simply supported beam carrying two point loads. The beam has the cross-section…

A: Figure is as shown

Q: A uniform structural tubing column AB with a height of 4 m has a cross section as shown in Figure…

A: The given data is shown below: Height=4mE=200 GPaA=2285 mm2r=37.5 mmI=3.33×106 mm4F=2e=18.75 mm

Q: A beam has a bending moment of 4 kN-m applied to a section with a hollow circular cross-section of…

A: Given bending moment M =4 KN-mdia of hollow section Do=3.3 cm=33mmand inner dia Din=2.3 cm=23…

Q: M N M X 8 mm N 8 mm t 50 mm 8 mm 50 mm

Q: The cantilever beam, whose loading condition and cross-section are given in the figure, is ideal…

Q: A rigid platform in Figure MEC-208 has negligible mass carries a center load P and rests or two…

Q: A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of…

Q: Q) A simply supported beam shown is loaded as shown in figurel-1. It has the cross section as shown…

Q: Determine the maximum bending stress (in MPa, numerical value only) of the beam shown belovw with…

Q: For a beam with the cross-section shown and loaded as shown, find the magnitude of the maximum…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5…

A: Given: The value of a is 4 in. The value of b is 5.3 in. The value of d is 4.5 in. The value of t is…

Q: A square cross-section cantilever beam is subjected to a force as shown below. What is the maximum…

A: Given :

Q: The beam shown in figure 3 is having a cross-section as shown in figure 4. Apply the flexure formula…

A: Draw the shear force and bending moment diagram of the beam as follows. Consider the given section.…

Q: The simply supported beam is subjected to the loadings shown in Figure Q2. Determine the value of P…

Q: A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa.…

Q: In the question in the image you can see a T-beam, but instead for solution assume inverted T-beam…

A: Draw the figure.

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.7 in., d = 4.1…

A: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

Q: The cantilever beam, whose loading condition and cross-section are given in the figure, is ideal…

A: Longitudinal section of beam: Beam Cross Section Stress-Strain Diagram

Q: the cantilever has a partially hollow circular cross section. If the admissible normal stress is 140…

Q: A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam…

A: Given: Beam width, b = 211 mm Beam height, d = 389 mm Load at the center, Pu = 63.66 kN Span of the…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

The cantilever T- beam is loaded as shown in the figure.
T.
80 mm
40 kN/m
NA
120 mm
2.0 m
INA = 30x105 mm
If the maximum flexural stress above the neutral axis is 100 MPa , What is the
value of the uniformly distributed load
when it is to be replaced by w in kN/m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q-5KN/m M=4KNM F=3KN L1=3m L2=1m L3=1m 8t M F JA 10t 2t L1 L2 L3 2t 4t
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
strength of materials
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
A cantilever beam having rectangular cross section with varying width band varying height h, is subjected to a uniform load of intensity, x L w. The width varies as The width varies as b = bo where x is measured from the free end and bo is the width of beam at the fixed end. If he is the beam height at the fixed end, the variation of height h, in order to have a fully stressed beam is
The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D What is the value of the flexural stress at the Neutral- Axis, NA?
Higdon
6. A cantilever beam with cross section shown in Figure 4 and span of 3.6 m is subjected to concentrated load (P) at the free end. If the maximum allowable shearing stress equals to 4 MPa what is the maximum value of the load P can be applied. 200 mm 40 mm 100 mm H 20 mm