1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q=5KN/m M=4KNM F=3KN LI=3m L2=1m L3=1m 8t M |A 10t 2t L1 L2 L3 2t 4t

1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q=5KN/m M=4KNM F=3KN LI=3m L2=1m L3=1m 8t M |A 10t 2t L1 L2 L3 2t 4t

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 Find the state of of stress for the element in Figure Q1 inclined by 30° counter clockwise by using: a) Equation Method b) Mohr's Circle Method 60 MPa Txy = 20 MPa 90 MPa Figure Q1
Determine the equivalent state of stress on an element if it is oriented 50° counterclockwise from the element shown. Assume that σ = -13 ksi and Txy = -19 ksi. Solve the problem using ox Mohr's circle. σχ F Part A Determine the normal stress ox'. Express your answer in kilopounds per square inch to three significant figures. ANSWER: = Tap image to zoom ksi Part B Determine the normal stress Øy'. Express your answer in kilopounds per square inch to three significant figures. ANSWER:
Solve for the equivalent force on an inclined surface. Look at Figure A.1 below. You will see a triangular block cut from a stress block with known stresses. The size and thickness of the block does not matter, so we will assume the area of the sloped inclined surface is A (sorry that it is the same symbol as the Point). If the area of the sloped surface is A, then the area of the other two surfaces is A cos (Theta) and A sin (Theta). First, draw a FBD of the block by multiplying each stress (normal and shear, known and unknown) by their associated area (in terms of A). Second, break the stress vectors on the side and bottom into components along the x’ and y’ axes. Third, sum the forces in the y’ direction and set them equal to zero (you should now be able to cross out the value of A for each term in your equation resulting in an equation with only one unknown, the normal stress in the y’ direction). Solve for the value of the normal stress in the y’ direction. Now repeat for…
PLEASE ANSWER ASAP TY! SEE THE FIGURE SHOWN a) What is the shear stress component (τ) on a plane at 35o counterclockwise from the x-plane (in MPa)? Include negative sign if it will cause counterclockwise rotation. b) Determine the angle of inclination of the principal planes in the differential element (in degrees). Include negative sign for clockwise rotational sense. c) Determine the minor principal stress σ2 (in MPa). Include negative sign if compressive. d) What is the normal stress component (σ) on a plane at 35o counterclockwise from the x-plane (in MPa)? Include negative sign if compressive. e) What is the magnitude of maximum shear stress (in MPa)?
Problem example Example 7-5: The state of plane stress at a point with respect to the xy- axes is shown in the figure. Using Mohr's circle, determine (a) The principal stresses and principal planes and sketch the results. (b) The maximum shear stress. (c) The state of stress with respect to the x'y'-axes. 20 MPa (+) A 16 MPa 50° X 40 MPa (+) 1. Omax 3. Op 7-42
. The biaxial stress system in an element is shown in the figure. Which of the following will give the normal stress in N/mm2 in the plane BD making an angle of 45° with the plane BA? 2 0₁ = 60 N/mm² C 0₂ = = 40 N/mm A A A 0₂ = = 40 N/mm 2 45 2 A B On 2 0₁ = 60 N/mm
An element in uniaxial stress is subjected totensile stresses σx = 57 MPa, as shown in the figure.Using Mohr’s circle, determine the following.(a) The stresses acting on an element oriented at anangle θ =-33° from the x axis (minus meansclockwise).(b) The maximum shear stresses and associatednormal stresses.Show all results on sketches of properly orientedelements.
NOTE: PLEASE SOLVE THIS QUESTION WİTH FINITE ELEMENT METHOD...solve 20 mins asap hand written
Please solve
Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and shearing stresses on the principal plane, and sketch the results. 18 MPa 60 MPa 15 MPA
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1400 mm, and the height of the plate is h = 1900 mm. The shear strain at A is known to be +4294 μrad. Assume a = 2.4 mm. Calculate the magnitude of dimension b in the figure. D h Answer: b= i A W Ta mm 2