6. A cantilever beam with cross section shown in Figure 4 and span of 3.6 m is subjected to concentrated load (P) at the free end. If the maximum allowable shearing stress equals to 4 MPa what is the maximum value of the load P can be applied. 200 mm 40 mm 100 mm 20 mm O O

6. A cantilever beam with cross section shown in Figure 4 and span of 3.6 m is subjected to concentrated load (P) at the free end. If the maximum allowable shearing stress equals to 4 MPa what is the maximum value of the load P can be applied. 200 mm 40 mm 100 mm 20 mm O O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum shear stress if its used as a 8m beam simply supported at the left end and 2m from the right and which carries a total uniform load of 40kN/m.
For the cantilever beam shown. find the value of Normal stress due to axial load at :point F FO ce A 10 m Diameter 100 mm 6 KN.m No stresses at point D 0 -31.229 Mpa +40.99 Mpa -0.25 Mpa +40.49 Mpa No stresses at point F No stresses at point A No stresses at point B +0.25 Mpa +40.74 Mpa No stresses at point C -40.99 Mpa +31.229 Mpa -40.74 Mpa +30.55 Mpa -40.49 Mpa +0.679 Mpa -0.679 Mpa No stresses at point E -30.55 Mpa
Solid
Answer the no.6 only
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
Corect answer.
SOLVE USING THREE MOMENT EQUATION
Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 129 kN, w = 22 kN/m a = 2.8 m, and b = 2.2 m. Determine the magnitude and location of the maximum bending stress in the beam. A omax = x = a i i P B a Pin C b MPa m W O D a E
A circular steel rod of diameter d is subjected to a tensile force P = 3.5 kN (see figure). P = 3.5 kN The allowable stresses in tension and shear are 171.0 MPa and 60.5 MPa, respectively. What is the minimum permissible diameter dmin of the rod (in mm)? mm
a beam of circular cross section is 7" in diameter is loaded as shown. the maximum bending stress is nearest to?
Problem 2: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a force that varies from 60 lb down to 100 lb up. There is a "fillet where the member is connected to the support which causes a theoretical stress concentration factor K+ = 1.32. The notch sensitivity factor q may be taken at 0.92. If the material has an ultimate stress s= 80,000 psi, an endurance limit in reversed bending s= 35,000, and a yield strength, s,= 60,000, determine: (a) maximum bending stress, (b) minimum bending stress, (c) mean stress, (d) variable stress, (e) design factor N.