The block has a mass of 4.5 kg and rests on the smooth plane as shown in . Part A k = 200 N/m 500000 450 0.3 m 0.4 m Determine the unstretched length of the spring.

Q: 1. T-square is used for drawing: A. horizontal lines b. inclined lines c. vertical lines d. lines at…

A: We have to find term 1,2,3

Q: Statics Question The diagram shows 2 vectors. Solve for the resultant vector (force and…

A:

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:-  Scale length = 84 mm Actual length = 63 m = 63000 mm  To Find:-  Scale

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: Answer by true or false for the following       Specific heat is a measurement of the ability of the…

A: The specific heat of a substance is defined as the amount of heat to increase the temperature of the…

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: F2 Find the x-component of F2 in Newtons. If the calculated answer is not whole number, express it…

A:

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: What is the modulus of toughness for steel B? Steel B 400 350 300 250 200 150 100 50 0.1 0.2 0.3 0.4…

A: Modulus of toughness for the steel B is the area under the stress-strain curve upto fracture.…

Q: dy Solve the differential equation cos(z) dz

A:

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: The figure below has the following weight per length. W₁ = 150 lb/ft W₂ = 175 lb/ft W3 = 130 lb/ft…

A: given;   w1=150lb/ftw2=175lb/ftw3=130lb/ftAB=1ftBC=6ftCD=4ftDE=5ftEF=8ftlets take reaction force at…

Q: F Find the y-component of F2 in Newtons. If the calculated answer is not whole number, express it in…

A:

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&amp;T symbols used in the image:Datum symbols: A datum is a…

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: Tentukan xz F.

A:

Q: Draw the orthographic Projections of given object.

A: Required orthographic views of the given isometric view are drawn on grid paper. 1 Grid = 1 Unit

Q: 8. Three ships A, B, C are located as follows: A is 48 km due north of B and C is 125 km due east of…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Represent the following as a number between 0.1 and 1000 using an appropriate prefix:568(10^5)mm

A: Given: The given number is N=568×105 mm. The conversion factor to convert the given unit in the…

Q: e boats A and B travel with constant speeds of VA = 18 m/s and 3= 11 m/s when they leave the pier at…

A: t=4sec

Q: Q1) For the given workpiece: a- Show the procedure used for finding the length AB and angle C using…

A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: Find the x-component of F1 in Newtons. Find the y-component of F1 in Newtons. Find the z-component…

A: The data given is, F1=400 N ϕ=41° θ=36°

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…