2 Constraint indicated the name and where it should be

Q: Support your answer with the appropriate solution and diagram. 3.Mercury makes an angle of 130…

A: Given:Angle made by the mercury, θ=130oDiameter of glass tube, d=2 cm=0.02 mSurface tension, σ=0.47…

Q: A 2.05-kN-m torque Tis applied to the solid cylinder made up of a hollow cylinder and an inner core…

A: Given:  Torque, T = 2.05 kN.m  Outer diameter, D = 50 mm Inner diameter, d = 25 mm  To find:…

Q: Its required to pump a liquid of specific viscosity of (15) poise at the rate of (22) iiters per…

A: When a fluid flows through a pipe, two forms of head loss (energy loss) enter the picture: one is…

Q: (A) Q: A 400 mm external diameter steel cylinder with a nominal internal diameter of 240 mm is…

A: (1) To find: The tangential stress at the outer surface of the inner cylinder. Given: The inner…

Q: The natural frequency of an undamped vibrating system is 100 rad/s. A damper with a damping factor…

A: Given data: ωn=100 rad/sζ=0.8

Q: 9. Air enters a heating section at 95 kPa, 12°C, and 30 percent relative humidity at a rate of 6…

A:

Q: Initially a household freezer com- partment is filled with air at room temperature T, = 27.0°C. Then…

A: Given:  Initial temperature inside the refrigerator, T1 = 270C = (27+273) K=300 K Initial pressure…

Q: The physics of the conduction heat transfer of thermosses phenomenon and the mathematical model…

A: A thermos flask consists of two bottles nested within one another with a vacuum layer in between.…

Q: 7. An oil (sp.gr 0.9) is flowing through a 1.2m diameter pipe at a rate of 2.5 m³/s. The kinematic…

A: Given:Specific gravity of oil, SGo=0.9Pipe diameter for oil, Dp=1.2 mFlow rate of oil, Qp=2.5…

Q: 4-3. The motion of the rigid body m is such that the point A moves in a circular path of 1-in.…

A:

Q: Determine the forces in members EH and EI of the double Fink truss. Neglect any horizontal reactions…

A: Given:

Q: An airfoil is tested inside a wind tunnel. The cross-section of the test section is rectangular as…

A: The flow is incompressible. The velocity expression is given as U=Ue(1-0.5cosπy2h Let the depth of…

Q: HYDRAULICS Support your answer with the appropriate solution and diagram. 1. An oil of viscosity 5…

A:

Q: 5. A block of m= 20 kg is acted upon by two forces as shown in the figure. (in m/s2) of the block?…

A: Given:Mass of the block, m=20 kgForces acting on the block:F1=40 NF2=30 N

Q: (a) The equation which describes the flow speed profile for a 1 v(r)=--((R²-²) Ap 4μ Ax pipe is:…

A: GivenVr=14μ∆p∆xR2-r2anddQ=dA×V

Q: A nuclear fuel element has the form of a plate 6 mm thick sandwiched between two stainless steel…

A: The heat generation rate is q=0.18*106 kW/m3. The thermal conductivity of an element is k=0.002…

Q: Figure 1 shows a binary phase diagram of elements A and B. Determine the phases present,…

A:

Q: The smooth pipe rests against the wall at the points of contact A, B, and C. Determine the reactions…

A:

Q: Chika Fujiwara loves to play games. Ever curious, she observes that a uniform disk 0 (mass = 0.500…

A: Before the cable becomes taut, no force is exerted by cable, thus only force which the disk…

Q: Using hfg, Vfg, and Psat at 20°C from the ammonia tables, estimate the saturation pressure, in bar,…

A: Given: Initial temperature: →T1=20°C At this temperature from the ammonia table: →hfg=1185.9…

Q: -4 Determine the optimum thickness from an economic point of view, of insulation for a steam pipe…

A: Given: Diameter of the steam pipe: →D=100 mm=0.1 m The conductivity of the insulation:…

Q: Compute the centroid of area and second moment area of area 20mm 20mm 100mm % 60mm 120mm -20mm

A: To find: The centroid and moment of inertia. Given: The given section is shown below.

Q: Problem 1 R22 saturated at 32°C is throttled to a pressure corresponding to a saturation temperature…

A:

Q: 6. Drive-in diffusion in ICs, is used to: A. Diffuse the impurity atoms into the silicon from a gas…

A: (6) The primary aim of the drive in Diffusion Process in IC Fabrication is to change the…

Q: 2. Honing is an operation performed as the operation. and 3. In sawing operation, the 4. For the…

A: Honing operation - In honing  a precision surface on a metal workpiece can be achieved by scrubbing…

Q: Rod AB rotates counterclockwise with a constant. angular velocity w 2 rad/s. The collar consists of…

A:

Q: i) Explain how to find moments in 3 dimentional systems ii) Find the resultant of vectors F₁, F2, F3…

A: Question 1 In 3 dimension system moment can be determined by cross multiplication of position vector…

Q: Know that h=0.25 m and that the gate, which has a pin connection at point C, is initially at rest.…

A: Introduction: The initial velocity of the bullet is given as, v = 550 m/s and is hitting and then…

Q: ● Consider the structure ACB: 1m 1m C 2m B α = 45° FB=50 [N] Question 1: Determine the moment with…

A: Given: The force at B, FB = 50 N The angle made by force with vertical = 45o

Q: Question One Crude oil of specific gravity 0.85 flows upwards at a volume rate of flow of 60 liters…

A:

Q: Given the forces, 60, 13, and 92, compute for the resultant force.

A:

Q: Ex. Given: Water is flowing through the pipe and vertical Orifice Plate Meter, as shown Water in jet…

A: A figure is provided and it is given that weight of vena contracta is 4lb. The force exerted on…

Q: Which technologies supported the development of residential suburbs and nuclear families? O The…

A: Nuclear family refer to the family which consist of core members of the family, usually parents and…

Q: HYDRAULICS Support your answer with the appropriate solution and diagram. 10.A rectangular plane…

A: Given:width of plate, w=1 mDepth of plate, d=3 mAngle with the horizontal, θ=30°Depth of the top…

Q: The liquid in Fig. P3.126 is kerosene at 20°C. Estimate the flow rate from the tank for (a) no…

A: Given data as per the question Pressure at surface = 20 lbf/in2 Atmospheric pressure =14.7 lbf/in2…

Q: Determine the moment of inertia of the cross-sectional area of the reinforced channel about the…

A:

Q: Consider a hybrid mechanical system shown in the figure below. Taking output as x3 and the input 0₁.…

A: Given: To find: Block diagram Transfer function

Q: Q9: Replace the three forces acting on the shaft by a single resultant force. Specify where the…

A: Find the single resultant force and specify where the line of action of resultant force intersect…

Q: = 1 rad/sec, constant. Find the vector for 4-7. Q₂B = 1 in.; BC = 3 in. w₂: A, by the relative…

A: Given: To find: Acceleration of C graphically

Q: 4.005 3.995

A: Given

Q: H PROB. 8-13. -2 that of T? E PROB. 8-14. -10% C 8-14. A and B are two shafts at right angles, in…

A:

Q: 10.27 Determine the defect frequencies in hertz* corresponding to roller, inner race, outer race,…

A: Given: Let us consider the given data, d=2 cmD=15 cmα=20°n=18N=1000 rpm To find: The frequency to…

Q: Sketch the crystallographic plane in unit cell.

A: given

Q: Sketch the following crystallographic planes in unit ce i) (221) ii) (110) iii) (101)

A: Given

Q: scuba tanks are often pressurized to about 3000 psi, or 44,100 atm at the start of the dive. What is…

A: Solution: Given Data: The 1st pressure inside the scuba tank is, P1=3000 psi The 2nd pressure inside…

Q: For the crank-rocker mechanism shown, determine the linear accelerations of points A and B, and the…

A: Given : Link 1 = 6mm Link 2 = 2mm Link 3 = 7mm link 4 = 9mm ω2= 30 rad/sec

Q: For the simply supported bar in the Figure, draw the Bending Moment (M) and Shear Force (V)…

A: Given: To find: Bending moment and shear force diagram

Q: Laminar Flow in a Vertical Cylindrical Annulus Derive the equation for steady-state laminar flow…

A: To find: The equation of steady state viscous flow. Given: The N-S equation is…

Q: R R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide…

A: Given: The length of the rod→L=0.545 m And it is equal to the radius of the circular slot. At the…

Q: T4. Sketch the schematic diagram of the Antenna Azimuth control system (position servo motor) as…

A: The schematic diagram of the antenna azimuth control system from the given figure is shown as below:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.