Solve for the resultant force.

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: A steel beam, of lengths a = 4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: A steel beam, of lengths a = 4 m and b = 4 m and a hollow box cross section, is supported by a hinge…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: a) What is the reading (degrees, minutes)? b) What is the reading (degree and fractions of a…

A: Reading on main scale = 90 degreeReading of vernier matching with main scale = 22Least count of…

Q: Metalworking According to standard American wire size tables, 3/0 wire is 0.4096 inches in…

A: Given: 3/0 wire is 0.4096 inches in diameter To  find: Write this size to the nearest 32nd of an…

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: Find the value of x5 in 3 decimal places (positive value) using Secant Method (5th Iteration) f (x)…

A: Write the given equation. fx=sinx-x take x0=0, then  f0=sin0-0=0 take x1=1, then f1=sin1-1=-0.1585

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Determine smaller diameter, All dimensions are in mm) 110.916 091 S 100.916 80.916 mm cant be…

A: The smaller diameter is 80.916 mm.

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A:

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: elow are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: According to the given dataAn orthographic projection view is given.We need to findmissing view of…

Q: A passenger train traveled to the repair yards and back. On the trip there, it traveled 52.32 kph…

A:

Q: Compute Ix (I sub x, in inches“, round-off to 2 decimal places) for the region shown. 4

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: need help finding dimension x and y in the casting shown 2.80 cm 5.20 cm 6.00 cm 2.50 cm E 7.20 cm

A: Draw a diagram for the given problem.

Q: Find the value of x5 in 1 decimal places (positive value) using Newton-Raphson Method f(x) = 2x2 + x…

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the…

A:

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E = 200…

A: The distributed load is The load is The modulus of elasticity is The moment of inertia is

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: Two 12' bars are cut into pieces 8-3/8" long and the saw kerf is 1/8" (waste). How many pieces can…

A: Given Data:- Length of each bar, L=12’

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.