The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: a) an expression for the bending moment at every point in the beam and draw the bending moment diagram b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100

The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: a) an expression for the bending moment at every point in the beam and draw the bending moment diagram b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
The figure below shows the cross-section of a beam that carries a vertical shear force, V= 72 kN. The distance from the bottom of the section to the NA is d= 267 mm and the moment of inertia of the cross-sectional area about the NA is I = 440 × 106 mm4. The maximum shear stress on this cross-section is: 60 mm 219 mm 225 mm NA ---- NA 36 mm ------ a 90 mm 90 mm d = 267 mm 225 mm 36 mm
A steel beam is simply supported at both end is laterally loaded as in Figure Q3a(i) to bend itplastically. The cross section is of hollow type and dimensions of the beam are shown in FigureQ3a(ii). If the steel behaves in elastic-perfectly plastic behavior with Yield Stress of 300 MPa,find out the value of load P, Shape Factor ƛ, Length of Plastic Lp when the critical section is inFully plastic condition.
An E-Shape beam with the cross-section is bent about vertical axis. As shown in Figure Q3, N-N is plastic neutral axis Assume that the yield stress, oy is 275 MPa and the elastic bending moment, My is 18.88 kNm, (i) determine the plastic moment, M, of the beam. (ii) determine the value of the shape factor for the beam. N 20 тm | 20 тm 100 тm 20 тm 60 тm 20 тm 80 тm N Figure Q3
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, a = 12 × 10°°C, and for aluminum assume E = 70 GPa, a= 25 × 10ºC. 200 kN 500 mm 80 mm -85 mm- 141 mm
Question # 4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. a a 0.5m 0.5m 30 kN 2 m 100mm 50mm A 10mm 10mm 180mm Section a-a 10mm
Figure Q3(a) shows an overhung beam AB that is subjected to point loads, P. The cross section of the beam illustrated in Figure Q3(b), and the material behaves linearly elastic-perfectly plastic with yield strength of 250 MPa. Taking the values of L = 2 m, and a = 1.2 m:a) Calculate the shape factor of the beam cross section.b) Calculate the load, Pp that will cause the beam to collapse (fully plastic) at the most critical location.c) What is the yielded length when the load, Pp in part (b) is applied?
For the beam shown in the figure below , determine the maximum bending stress
Q36 onlys Ratio of stress in part A and B
A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the compressive stress in MPa? I am new to the subject but why use .....AC = π * (D2 - d2) / 4 instead of A = π(r12 - r22) to find the cross sectional area of a hollow cylinder ?.
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in) a (PF) E (GPa) Steel Rod 300 11.7 x 104 200 Bronze Rod 1400 18 x 106 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m W