A simply supported beam is loaded as shown. Using double integration method withE = 21.8 x 10 kN/m2 and I = 0.0072m", determine;a. the slope of the elastic curve at support A.b. the deflection at point D.c. the deflection at poin C.20kN↓3m3m50kN 30KN↓2m 210 kN/mс

Answered: Image /qna-images/answer/126de1a2-02fb-4709-9950-1ecb290d0d65.jpg

A simply supported beam is loaded as shown. Using double integration method with E = 21.8 x 10 kN/m2 and I = 0.0072m², determine; a. the slope of the elastic curve at support A. b. the deflection at point D. c. the deflection at poin C. 20KN ↓ 3m 3m 50kN 30KN ↓ 2m 2 10 kN/m с

A simply supported beam is loaded as shown. Using double integration method with E = 21.8 x 10 kN/m2 and I = 0.0072m², determine; a. the slope of the elastic curve at support A. b. the deflection at point D. c. the deflection at poin C. 20KN ↓ 3m 3m 50kN 30KN ↓ 2m 2 10 kN/m с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected…

A: Total length of both pipe=2l To find diameter of second pipe

Q: Current Attempt in Progress The smooth concrete-lined channel shown in the figure below is built on…

Q: A pile of diameter 0.4 m is fully embedded in a clay stratum having 5 layers, each 5 m thick as…

A: Given- Diameter of the pile d=4 m, Unit weight of soil=18 kN/m3, It is needed to find the value of…

Q: Water flows in a tube that has a diameter of D = 0.4 m. (a) Determine the Reynolds number if the…

A: Reynolds number is a dimensionless number which is used to find the type of flow in a pipe.…

Q: A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in.…

A: Given: 6 ½ inch steel bolt 4 ¾ inch aluminium bolt Allowable stress in steel = 9000Psi Allowable…

Q: If you were a controller for a major urban county readiness exercise, what factors and criteria…

A: Disaster readiness may be a core part of disaster risk management and is crucial for providing an…

Q: Current Attempt in Progress Cable AB passes over the small ideal pulley C without a change in its…

Q: Current Attempt in Progress Water flows in the channel shown in the figure below at a rate of 90…

Q: 3. List at least three and include pictures of the world's tallest wooden buildings

A: As per question requirements , I answered only Question number 3. This question is related to…

Q: Water vapor enters a turbine operating at steady state at 1000°F, 190 lbf/in², with a volumetric…

Q: One of the three landing pads for a proposed Mars lander is shown in the figure. As part of a design…

Q: Draw the complete shearing force diagram for the beam shown below. A 2 m 120 kN B C 1 m 36 kN/m -3…

A: Objective: To draw the shearing force diagram for the given beam. The shearing force diagram will…

Q: 2. A lock is a device used for raising and lowering boats, ships and other watercraft between…

Q: The rectangular canal shown in the figure below changes to a round pipe of diameter D as it passes…

A: Given: Required: Determine D in terms of b

Q: A semicircular gate (A-B) is hinged along the shaft at the bottom (B) of a water reservoir (density…

A: The specific weight of water, γw = 62.4 lbft3 The radius of the semicircular gate, R = 10ft The…

Q: Problem 10.28 Consider the channel shown in (Figure 1). Suppose that a = 370 mm, b = 210 mm, c = 50…

Q: If P₁ = 5.3 lb, P₂ = 5.3 lb, P3 = 10.3 lb, and dc = 3 m, determine the reaction at E and the…

Q: 2. For the frame given, determine the moment M/ which must be applied at the pin support to keep the…

Q: A 60 kN/m 2.0 m B 120 kN.m 3.0 m 30 kN C 3.0 m D

Q: Reaction Force at Joint A? Reaction Force at Joint I? Member C or T AB AC BC BD CD CE DE DF FE FH EH…

A: Data given

Q: 5. For frame presented in Fig. 5, calculate the reactions at the two supports under the applied…

Q: Classify the following truss as statically determinate, statically indeterminate, or unstable; also…

Q: Two horizontal plates are placed 2 cm apart. The space between them is filled with oil of viscosity…

A: Given data : Two horizontal plates are placed 2 cm apart and filled with oil Find : Shear stress…

Q: Problem 9.1. The figure below shows information from monitoring wells sampling from subsurface…

A: As per our company Guidelines we are only allowed to answer any 3 questions. So please specify the…

Q: O A fillet -welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90…

Q: Consider a solid shaft of 1.4-in. diameter. Determine the maximum shearing stress in the shaft as it…

A: Given data Power (P) = 66 hp N = 780 rpm Diameter of solid shaft (d) = 1.4 in Find maximum…

Q: Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional…

A: Given data E = 200 GPa A = 600 mm2 Find vertical deflection of joint-A using Castigliano's…

Q: Water flows in a channel as shown in the figure below. The velocity is 7.5 ft/s when the channel is…

Q: Reciprocal leveling gives the following readings in meters from a set up near A: on A, 1.110; on B,…

Q: (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected…

A: To find diameter of second pipe

Q: Determine the magnitude of the moment of the force P (3104-200j + 150k) N about the z ans (Egure 1)

Q: Aluminum is a poor material to reinforce concrete with, especially as opposed to steel. There are…

A: Solution Introduction: The steel is used as reinforcement in the concrete to take the tension loads…

Q: Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that Q = 10…

A: Given: Required: Value of P

Q: Draw the influence lines for the force of truss members AB, BG, DF, FG. LES U F D 1.5m 1.5m 11.5m /…

Q: Locate the centroid of the shaded plane area shown

A: Divide the plane area into a rectangle and two quarter-circles as shown in the figure. Radius of…

Q: The rigid frame shown is unbraced. The members are oriented so that bending is about the strong…

Q: A field channel has cultivable commanded area of 2000 hectares. The intensities of irrigation for…

Q: show how did you get the final answer from the result of integration

Q: A triangular gate with a base width of 2 m and a height of 1.5 m lies in a vertical plane. The top…

A: Given- Base Width=2 m, Height =1.5 m, Specific gravity=0.8, Density of water =1000 kg/m3,…

Q: For the frame and loading shown, determine the components of all forces acting on member ABC. 1.2 m…

Q: SHOW THE DIAGRAM AND YOUR COMPLETE SOLUTION: 4. A car requires 46m to stop after the application of…

Q: 2. For the frame given, determine the moment M which must be applied at the pin support A to keep…

A: Given : Calculate the magnitude of reaction force component at A ?

Q: An Accessible Route can be broken and restarted if the break in accessiblity is less the 30 feet and…

A: As part of an accessible route, all walkways, halls, corridors, aisles, skywalks, tunnels, and other…

Q: Why can't aesthetic features affect the stability of the bridge?

A: The following factors must be met for bridge pier stability: the foundation's sustaining earth, and…

Q: A 2-in pipe line leads downhill from a reservoir and discharges into the air. If the loss of head…

A: Given Diameter of pipe = 2 in

Q: Lubricating oil at 20°C with a density of 871 kg/m³ and a kinematic viscosity of 1.5 x 105 m²/s…

A: Density of the oil = 871 kg/m3 Kinematic velocity (ν) = 1.5×10-5 Inner radius (Ri) = 0.04 m Outer…

Q: A viscous oil with a specific gravity SG = 0.85 and a viscosity of 0.10 Pa s flows from tank A to…

Q: 2.38 A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in…

A: Given: Hinge at the top of the gate. Width of rectangular gateB=4 ft. Length of rectangular gateL=6…

Q: Describe the gravity-based transportation of soil and its cycle back to the upstream to elevated…

A: Soil are classified in different types on the basis of their transportation.

Q: What will be polar moment of inertia of a solid circular shaft having a diameter of 150 mm?

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Question

A simply supported beam is loaded as shown. Using double integration method with
E = 21.8 x 10 kN/m2 and I = 0.0072m", determine;
a. the slope of the elastic curve at support A.
b. the deflection at point D.
c. the deflection at poin C.
20kN
↓
3m
3m
50kN 30KN
↓
2m 2
10 kN/m
с

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The compound beam is subjected to the loadings as shown in the figure below. Use E-200x106 kPa and I=125x106 m². Determine the following: a. The deflection at A; b. The slope at point B; c. The displacement at D; and d. The illustation of the elastic curve of the compound beam. A 1.0m 1.5m B 18 kN 3m 35 kN-m 1.5m D 3m 14 kN/m Jooh
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum shear is 444.9kN. Let, P=170kN, a=2.5m, b=1m and c=3m ; If the deflection at the free end (leftmost part of the beam) is equal to -14.183444485219mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam
Using the virtual work method, detemine the vertical displacement of joint Cof the steel truss shown in Figure Q3. Assume E= 200 GPa and A = 500 mm for all members. 4 m 300 kN Im 120 kN 4m 4m Figure Q3
Determine the following unknowns on the beam shown below using AREA-MOMENT METHOD. Consider 150mm x 150mm section and E = 80 GPa. Show complete and organized solution. Solve the following: - Vertical Reaction at B in kN. - Moment Reaction at A in kN-m. - Deflection at point C in mm. - Deflection at midspan of AB in mm.
A beam 2.4 m long is simply supported at two points A and B which are 1.44 m apart; point A is 0.36 m from the left-hand end of the beam and point B is 0.6 m from the right-hand end; the value of EI for the beam is 240×10® Nmm². Find the slope at the supports due to a load of 2 kN applied at the mid-point of AB. Use the reciprocal theorem in conjunction with the above result to find the deflection at the mid-point of AB due to loads of 3 kN applied at each end of the beam. Ans. 0.011, 15.8 mm.
4. By using Double Integration Method, Determine the deflection 3m to the left of roller support. 30 kN/m 55 KN 9 m El = constant E = 200 GPa 1 = 830 x 106 mm4 (a) Real Beam -3 m-
has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 170 mm. %3D %3D 250 mm 180 mm
The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 24 kN, M = 16 kNm, L1= 2 m, L2 = 6, L3= 2 m and a=20 mm. Find, a. by double integration method, the ElS at the right end of the beam b. by double integration method, the maximum El6 between supports c. If w is spread over the entire length and P and M are interchanged, determine the midspan EIS and deflection by moment - area method. ба B. M CO D 10a L2 За
For the bearn and loading shown, use discontinuity functions to compute (a) the slope of the bear at B and (b) the deflection of the bearn at A. Assure a constant value of EI = 115000 kip ft² for the bear; wo = 2.8 kips/ft, LAB = 12 ft. LBC = 6 ft. Wo Answer: (a) 8B = (b) VA = LAB rad in. B LBC C X
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A L Find the deflection at point C. 20 N B 1.5W, N/m H Figure 1: Overhang beam L C Set wo = 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
Given the figure below. Use UNIT LOAD METHOD in determining the maximum deflection at midspan. E and I are constant. 1. What is the reaction at A of the real beam? 2. In constructing the virtual beam and determining the maximum deflection, where must be the 1-unit load be placed? 3. What is the reaction at the support of the virtual beam? 4. In solving the maximum deflection at midspan, how many portions or segments must the beam be divided so that the real and virtual loadings are continuous in each segment? 5. Consider segment AB of the real beam, with x measured from A, what is the moment equation M_(AB ) ? 6. In question 4, what are the limiting values of x? 7. Consider segment AB of the virtual beam, with x measured from A, what is the moment equation? 8. Analyzing segment BC of the real beam, with x measured from A, what is the moment equation M_BC? 9. In the given beam, if the 50 KN load is moved 2m closer to A and deflection at midspan is desired, how many segments must the…