The beam carries a concentrated load P and a uniformly distributed load that totals 3P. Determine the largest allowable value of P if the working stresses are 50 MPa in tension and 80 MPa in compression. Compute for the support reactions and draw the load, shear and moment diagram using either of the 2 methods discussed. Show your complete solution. ЗР (total) B 20mm - A Smm 5mm 15mm - →k- 2 m· 4 m 5mm -10mm-

The beam carries a concentrated load P and a uniformly distributed load that totals 3P. Determine the largest allowable value of P if the working stresses are 50 MPa in tension and 80 MPa in compression. Compute for the support reactions and draw the load, shear and moment diagram using either of the 2 methods discussed. Show your complete solution. ЗР (total) B 20mm - A Smm 5mm 15mm - →k- 2 m· 4 m 5mm -10mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
The AD beam, which is fixed at left end, is under various loads as shown below. a) Draw internal load diagrams (Nx, Vy, M2) using the method of section. b) Determine the state of stress at points G, H and I for section B. c) For the corresponding points, indicate the results (i.e. stress components) on a differential element. b2 A B G М F2 2l h bi GIVEN DATA: Fo = 10000 N, F1 1200 N, F2 = 1000 N, qo = 50 N/cm, Mo = 50000 Nem, l = 25 cm bi = 10 cm, b2 = 20 cm, h 12 cm, t 1 cm
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined together by a pin with a diameter of 60mm. 200 mm 60 mm P 160 mm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. Suppose that P is 140KN, the Modulus of Elasticity is 200GP,, and the Poisson's ratio is 0.3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. 4) Determine the change in thickness of each plate.
M E You have 2 Thank You Best Regare Ms. Nur Akr Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load are applied to the truss as shown in the Figure. By using section method, solve the force in member AC, CD and DE in the figure shown (CO2, PO2, C3). 20KN 10KN 3.5m H →10kN 3.5m E 3.5m D H 15kN 10kN- 5kN G C A 5.0m 3.5m B 000 5kN 5kN Gmail M
Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the followings and show them on a differential element. a) Principal stresses and its orientation b) Maximum in-plane shear stress and its orientation t 7 kN/m 2 m A - -2 m FATT 5 mm 5 mm 50 mm B t 5 mm → *F 3 mm Section A-A 80 mm
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa -34MPA
Q1/ A thin-walled cantilever has a constant cross-section of uniform thickness with the dimensions shown in Figure. It is subjected to a system of point loads acting in the planes of the walls of the section in the directions shown. Calculate the direct stresses according to the basic theory of bending at the points 1,2 and 3 of the cross-section at the built-in end along the beam. 50N 2 mm 50 N 80N 2 mm 100 mm 2 36 mm 80 mm 24 mm