The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I=843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, LBC = 7 ft, LCD= 7 ft, LDE = 7 ft.

The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I=843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, LBC = 7 ft, LCD= 7 ft, LDE = 7 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need help!
The simply supported beam consists of a W21 × 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.8 kips/ft, determine:(a) the beam deflection vA at point A.(b) the beam deflection vC at point C.Assume LAB = 10 ft, LBC = 8 ft, LCD = 8 ft, LDE = 7 ft.
I need the answer to the question in reinforced concrete
answer only letters D and E
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; /= 370 × 106 mm4]. For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, LAB = LBC= 2.9 m, LCD = 2.9 m. P "| พ X C LBC A Answer: Vc= LAB B mm. LCD
A rigid beam AB is hinged at A and is connected to an aluminium alloy bar BC at the other end. The beam is also supported on a steel post DE through a rigid bearing at D, as shown is figure. At no load condition, the beam is horizontal and there is an initial clearance 8 = 0.1 mm between the beam and rigid bearing. Determine the maximum permissible load W which may be applied at B if the axial stresses are not to exceed 120 N/mm² for steel and 140 N/mm² for the aluminium alloy. All the connections may be treated as smooth pins. Take E = 2 × 105 N/mm² for steel and E=0.8 x 105 N/mm² for aluminium alloy. A 0.2 m 0.1 m D Rigid beam 8- 0.1 mm Steel post (1500 mm²) E 0.3 m W C B Aluminium alloy bar (800 mm²) 0.4 m
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I-1730 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 210 kip-ft, P = 13 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A Answer: (a) VA = (b) VB = LAB P B in. in. LBC C - X
stion 27 1 points Save Answe A built up l-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.5 m long. All elements are A36 steel and connected such the section is fully effective. Using the following properties, calculate the flexural buckling stress, Fer, in MPa using theoretical k. Flanges: b = 150 mm, t = 17 mm Web: h= 310 mm, tw - 7 mm Write your final answer in two decimal places only. I L tw
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b
*4-88. If the allowable normal stress for the bar is = 120 MPa, determine the maximum axial force P that can be applied to the bar. σ O allow PA 40 mm 5 mm 20 mm r = 10 mm 20 mm Probs. 4-87/88 P
The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; 1= 351 x 106 mm*]. Determine the beam deflection at point A. (a) (b) the beam deflection at point C. Assume P = 39 kN, w = 61 kN/m, LAB= 3.6 m, LBC= 3.6 m, LcD = 3.6 m, LDE = 1.8 m. Answer: VA= P Vc = I B LAB LBC mm mm LCD W D LDE E X