The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2. The beam ACE is subjected to the force P-163 N. Take L=1.6 m and d=519 mm. Answer the following questions B D A E

The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2. The beam ACE is subjected to the force P-163 N. Take L=1.6 m and d=519 mm. Answer the following questions B D A E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 109 GPa] with a cross-sectional area of A₁ = 530 mm². Bar (2) is an aluminum alloy [E = 64 GPa] with a cross-sectional area of A2 = 330 mm². A concentrated load of P = 67 kN acts on the structure at D. Assume L₁=740 mm., L₂=500 mm., a=660 mm., b=310 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar.
134.439 is not the answer. Thank You
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
Subject: Static of rigid bodies Find: Shear Diagram of beam 1, 2, and 3. Show me the solution pls thank you!
Please show complete solution. Thank you!