FindOF g, C, I, A', ğ,bthevalueA' = areaabove= the distance from the center oF A to the centroidal axismomentIner tiaOFbasethe centroidal axisOF are aaboveattachedtロC = the distance From tne center to the topmost Fiber OF the bcamFormulas:Fb= McエIbFb=bending stressv: shearing stressM = ma x valueOF momentOFshear: E ayATo. 0ammO.004mm0.02mm0.12 m m

Find centroid:y=∑ Ay∑ A=0.02×0.0040.02+0.0042+0.02×0.120.0220.02×0.004+0.02×0.12y=0.0063137mm

Answered: Find y. c, I, A,y.b the value OF

Engineering

Civil Engineering

Find y. c, I, A,y.b the value OF

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 680 mm² and an elastic modulus of 29 GPa. Bar (2) has a cross-sectional area of 1580 mm² and an elastic modulus of 15.2 GPa. Determine the deflection of point A relative to support C. 70 KN 0.85 m O -1.902 mm O-2.101 mm O -2.250 mm O-1.354 mm O -2.879 mm 90 kN (1) 90 kN B (2) 1.15 m
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
The length of the 2 mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 2 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=200GPA, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D 0.3 m | 20 kg 2 mm 0.3 m 0.1 m
Static of Rigid Bodies Prob 03: Locate the centroid of the plane area shown: y 4 in. -8 in.-
Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
+y A B a +x 12 Three coplanar, concurrent forces at O Horizontal component of force B will act along_ negative x-axis negative y-axis positive x-axis positive y-axis
19e m Find the total deformation of 14022 the bar with circular cross- Section of 3cm diameter. E = 1440 x10³² MPa. it your bones van L x 2m x f=4x kr/m 3m
STRESSES IN BEAMS Problem 2 The simply supported beam in Fig. (a) has the T-shaped cross section shown. Determine the values and locations of the maximum tensile and compressive bending stresses. 400 lb/ft 1000 lb - 6 in. Į C0.8 in. D A 0.8 in.- 8 in. - 4 ft- Rg = 3400 lb 10 ft R = 1600 lb %3D %3! (a)
Select all true statements. The properties that can reduce the shear strength ofdiscontinuities are: Reduced spacing between discontinuitiesSoft infilling materialClosed discontinuities Increased roughnessDiscontinuity inclined at an angle (45+b/2)° to o1
3) The plate shown is fixed connected along AB and held in the horizontal guides at its top and bottom, AD and BC. If its right side CD is given a uniform horizontal displacement of 4 mm, determine (a) the average normal strain along the diagonal AC, and (b) the shear strain at E relative to the x, y axes y. i= 340 mm j= 479 mm D k = 170 mm A k E j k B i 4тm
If the applied force P causes the point B on the rigid arm ABC to be displaced 0.1 mm downward, determine the normal strain developed in wires BD and CE. E 600 mm D 400 mm B 400 mm 600 mm undefined
Learning Goal: To solve for forces in statically indeteminate bars with axial loads The square bar shown (Figure 1) is 70 mm thick and 4.8 m long and is fixed supported at both ends. Aload directed leftward s appled at point C, as shown, La =3.02 m from the left end. The modulus of elasticity is E = 100 GPa if point C maves 8 = 0 175 mm to the left what is the applied force? When the number of reaction forces is greater than the number of equilitrium equations, the system is Express your answer with appropriate units to three significant figures. statically indeteminste Solving for the reactions requires some additional equations. These additional View Avallable Hint(s) equations come from considering compatibility relationships (1e, continuity of displacements and relationships berween displacements ana ioads). For an axially loaded member, the compatibility relationship for the deflections can be written by setting the total relative axial displacement between the ends of the member…