The assembly shown in Figure 5 consists of two sections of galvanized steel pipe connected using a reducing coupling at B. The smaller pipe AB has an inner diameter of de 16 mm and an outer diameter of do 18 mm, whereas the larger pipe BC has an inner diameter of dae 21 mm and an outer diameter of dae 24 mm. Take Lan Lec 250 mm and G = 25 GPa. If the pipe is tightly secured to the wall at C. determine the angle of twist at point A. LAM 75 N 150 mm- 200 mm L

The assembly shown in Figure 5 consists of two sections of galvanized steel pipe connected using a reducing coupling at B. The smaller pipe AB has an inner diameter of de 16 mm and an outer diameter of do 18 mm, whereas the larger pipe BC has an inner diameter of dae 21 mm and an outer diameter of dae 24 mm. Take Lan Lec 250 mm and G = 25 GPa. If the pipe is tightly secured to the wall at C. determine the angle of twist at point A. LAM 75 N 150 mm- 200 mm L

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
The assembly shown in the figure below consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smallor pipe AB has an inner diameter of d1in=16.8 mm and an outer diameter of d1out=18.2 mm, whereas the larger pipe BC has an inner diameter of d2in=21.4 mm and outer diameter of d2ou=23.08 mm . Take LAB = LBC = 250mm and G=25 GPa. If the pipe is tightly secured to the wall at C, determine the maximum shear stress in the pipe assembly. Present your answer in MPa unit with two decimal points
Write the solution for the following: Member BC= 600 N Member FG = -600 N
Problem: The steel pipe has an inner diameter of 2.75 in and an outer diameter of 3 in. The pipe is fixed to the ground at C, and a wrench is attached to the opposite end. The wrench is subjected to a horizontal force of 20 lb that acts in -z direction. Points A and B are located on the surface of the pipe at the same cross section. Note that A lies directly above the -y axis, and B lies directly above the +z axis. 20 lb 10 in. A B y 12 in. (a) Find the normal and shear stresses at points A and B. (b) Find the principal stresses at points A and B. (c) Show all stresses from parts (a) and (b) on properly oriented elements, relative to the given coordinate system.
Q 2: The homogeneous wire ADOBC is bent into a semicircular arc and two straight section as shown. It is attached to a ball and socket at O and also to the cable AE. Dimensions are BC=20mm, BO=40mm,OE=90mm, R=60mm. Load conditions are; F=20 N single load direction E to D point , V=10 N force couple at B and C point , q N/mm distributed load on OB , homogeneous wire weight is neglected. Determine a) The reaction force at O point is a ball and socket b) The tension in cable AE. c) q (N/mm) distributed load value. E D 40 mm 60 my 20 mm
B The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their other ends are fixed. Lengths of AB and BC are 150 mm and 120 mm, respectively. They have uniform cross- sections all over their lengths and the details of their cross sections are given on the figure. Here, ri=28 mm and r2 =45 mm. and both have a wall thickness of 4.2 mm. The ultimate shear strengths of the copper and aluminum are 150 MPa and 70 MPa, respectively. Determine the maximum value of torque, T in elastic limits. АВ BC
66 ll ? e V:09 The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m D. 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
Pii The dimenstons of the various links of a freumabre riveter, as shown in hy Q-V , { OA = 175mm, AB- 180 mm, AD = 500 mm, and BC= 325mm Find the velo city rettio betuem) C and ram D when OB is verheal, (Ans= 医:L4) 45 A
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
IN THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND B ON THE PIPE ACCORDING THAT THE PIPE'S DIAMETER IS 25 mm; FIND MAXIMUM and MINIMUM SHIPMENT STRENGTHS AT POINT A.