The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be expressed by the equation t = (kx²) N• m/m, where x is in meters. If a torque of T = 50 N · m is applied to the bolt head, determine the constant k and the amount of twist in the 50-mm length of the shank. Assume the shank has a constant radius of 4 mm. B >T= 50 N-m 50 mm dT = t dx 0.05 m SON.M

The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be expressed by the equation t = (kx²) N• m/m, where x is in meters. If a torque of T = 50 N · m is applied to the bolt head, determine the constant k and the amount of twist in the 50-mm length of the shank. Assume the shank has a constant radius of 4 mm. B >T= 50 N-m 50 mm dT = t dx 0.05 m SON.M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB shown below can be expressed by the equation t = (kx² ) N-m/m, where x is in meters. If a torque of T = 50 N-m is applied to the bolt head, determine the constant k and the amount of twist in the 50-mm length of the shank. Assume the shank has a constant radius of 4 mm. 50 mm T = 50 N-m
The assembly consists of two steel bolts AB and EF and an aluminum rod CD. When the temperature is at 30 °C, the gap between the rod and rigid member AE is 0.1 mm. Determine the force in the bolts (AB, EF) and the rod (CD) if the temperature rises to 130 °C. Assume BF is also rigid. 0.1 mm Steel bolts AB.EF E = 200 Gpa a=14x10/C Aluminum rod CD E = 68.9 Gpa a=24x10/C 25 mm 25 mm 400 mm 300 mm 50 mni D.
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15- mm diameter 304 stainless steel rod EF, and a rigid bar G. 1) If P=5KN, determine the horizontal displacement of end F of rod EF 2) If the horizontal displacement of end F of rod EF is 0.45 mm, determine the magnitude of P. -300 mm- 450 mm- Figure 3: Assembly 4P
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring F and the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² E 6 ft -1 ft2 ft- AEF 2a in² 2 ft FO 60 kip D ACD= 1.5a in² C
2) The bolted connection shown in the figure uses SAE grade 8 bolts. The members are hot-rolled AISI 1040 steel. A tensile shear load F = 5000 Ibf is applied to the connection. Assume the bolt threads do not extend into the joint. Find the factor of safety for all possible modes of failure. in- →1ş in→< in in in-18 UNC in
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
Auniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P- 7 KN, Determine the axial deformation of uniforn bar 1 (in mmi. Indicate negative sign if compression. 5P O 3P E-200 GPa gomm o mm Z so mm 30 mm 30 mn 30 mm 80 mm
The assembly consist of two 10mm diameter red brass C83400 Copper rods AB and CD, a 15mm diameter 304 stainless steel rod EF, and a rigid bar G. The modulus of elasticity for red brass C83400 is 101 GPa for 304 stainless steel 193 GPa. If P= 4.3 kN, determine the horizontal displacement of end F of rod EF
For the assembly shown, as the screw is tightened down, the strain in the horizontal direction at B is 900×106 m/m. What is the load P on the screw. E= 200 Gla.= of le 20 60 20mm hans s 201 Bo 40 Section a-a 104mm a← 120mm IT. at 300 mm →
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring F and the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² AL 6 ft E 1 ft2 ft- AEF=2a in² 2 ft FO 60 kip D ACD = 1.5a in² C