Part AIf the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten itdown. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35.Express your answer to three significant figures and include the appropriate units.M = 1.1142NmO The unit you entered is not recognized. Review a list of acceptable units.No credit lost. Try again.SubmitPrevious Answers Request AnswerFigure1 of 1Provide FeedbackNext >MO Pearson

Above given data we have to find torque M

• Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is ls = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure < 1 of 1 > Provide Feedback Next > O Pearson

• Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is ls = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure < 1 of 1 > Provide Feedback Next > O Pearson

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure below shows a shaft of three segments. It is restrained (fixed support) at both sices and is loaded by two torques. Use Groze -35 GPa, Glum - 28 GPa, and Getee - 83 GPa Aluminum Steel Bronze digmeter = 50 mm diameter = 25 mm diameter = 25 mm T-300 N.m K To =700 N.m4K 2 m 2 m 2.5 m Determine the maximum shearıng stress developed in aluminum. Select the corect response 214.16 MPa 175 MPa 57.12 MPa 111.79 MPa
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
Brass. (c). A bar of length 1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter being 10 mm as shown below. Under a load of 30 kN, if the extension of the bar is 0.222 mm, what is the modulus of elasticity of the bar? mam um
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The connection consists of three 5/8-in. bolts that join two 1/4-in. end plates welded to the brace and a 5/8-in. gusset plate welded to the column. The compressive load P carried by the brace equals 8.0 k. Determine the following quantities: (a) The average shear stress (τ)ave in the bolts, and (b) the average bearing stress (σ)b between the gusset plate and the bolts. (Disregard friction between the plates.)
A bracket connection shown in figure, consists of a joist cutting welded to the flange of a column by shop fillet welds 8 mm on flanges and 6 mm on the web. Determine the safe service load 'W', the bracket can support at a distance of 200 mm from the face of the column if the steel grade is Fe 410. 200 200 8V 150 200 W 8 V 150 N 150 200 250 Partial factor of safety on shop weld = 1.25 Yield strength of steel = 250 MPa. 250 A
The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table. Determine: a. The maximum force P that can be applied at C. Answ: 84.22 kN. b. The deformation at the point where the load is applied. Answ: 1.5278 mm.
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0