The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring Fand the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² AEF 6 ft F E |--1 ft2ft = 2a in² 2 ft 60 kip D ACD = 1.5a in² C

The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring Fand the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² AEF 6 ft F E |--1 ft2ft = 2a in² 2 ft 60 kip D ACD = 1.5a in² C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Two steel tubes are joined at B by four pins (dp = 11 mm), as shown in the cross section a – a in the figure. The outer diameters of the tubes are dAB = 40 mm and dBC = 28 mm. The wall thicknesses are tAB = 6 mm and tBC = 7 mm. The yield stress in tension for the steel is (y = 200 MPa and the ultimate stress in tension is (U = 340 MPa. The corresponding yield and ultimate values in shear of the pine are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing between the pins and the tubes are 260 MPa and 450 MPa, respectively. Assume that the factors of safety with respect to yield stress and ultimate stress are 4 and 5, respectively.Calculate the allowable tensile force Pallow considering tension in the tubes.Recompute the Pallow for shear in the pins.Finally, recompute Pallow for bearing between the pins and the tubes. What is the controlling value of P?
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm