Suppose the machine is initialized to its starting state '00' and then processes the input values: 1,0,0,1,0,0 (1 input bit after each Clk). What sequence of outputs does it produce, the state transitions, and what is its final state? D- Design the logic circuit of this FSM using JK flip flop? Next State Output Present State x -1 x -1 A B+C B 0. 1 1 1. 0. 0. 0ooo

Suppose the machine is initialized to its starting state '00' and then processes the input values: 1,0,0,1,0,0 (1 input bit after each Clk). What sequence of outputs does it produce, the state transitions, and what is its final state? D- Design the logic circuit of this FSM using JK flip flop? Next State Output Present State x -1 x -1 A B+C B 0. 1 1 1. 0. 0. 0ooo

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q4) Design a Register File which includes four 2-bit registers (In total, it includes 8 bits). Each register is named as ala0, b1b0, c2c0, d1d0. Registers are loaded from the S input. In addition to that, there are two input signals, X and Y, to determine which register to select (ie. 00 selectsfirst register ala0 etc). Also there is R signal. When W is zero, the content of the register does not change. When the W is 1 the selected register is loaded with a new value by shifting from the S input. Design this register file by using D flip-flops.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Up/Down State Machine Cousider a state machine implementation of a two bit up/down counter mput: up/doun, and two outputs: Outo and Out,, which also indicate the next state. When up/dowTI is high, the counter counts up (00,01,10,11,00, ). When up/doun is low, the counter counts down (00,11.10.01.00, ..). The state machine has one Part A Complete the state diagram below by adding all required transition arcs with input annotations. Output annotations are not required since they correspond to the new state. state state 00 01 state state 10 11
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110