Up/Down State MachineCousider a state machine implementation of a two bit up/down countermput: up/doun, and two outputs: Outo and Out,, which also indicate the next state. When up/dowTIis high, the counter counts up (00,01,10,11,00, ). When up/doun is low, the counter counts down(00,11.10.01.00, ..).The state machine has onePart A Complete the state diagram below by adding all required transition arcs with input annotations.Output annotations are not required since they correspond to the new state.statestate0001statestate1011

As a self-reversing counter, the UP/DOWN counter might be utilized. It may also be used as a clock…

Up/Down State Machine Consider a state machine implementation of a two bit up/down counter The state machine has ope input: up/doun, and two outputs: Outo and Out,, which also indicate the next state. When up/doen is high, the counter counts up (00,01.10,11,00, ). When up/doun is low, the counter counts down (00,11.10.01.00, ). Part A Complete the state diagram below by adding all required transition arcs with input annotations. Output annotations are not required since they correspond to the new state. state state 00 01

Up/Down State Machine Consider a state machine implementation of a two bit up/down counter The state machine has ope input: up/doun, and two outputs: Outo and Out,, which also indicate the next state. When up/doen is high, the counter counts up (00,01.10,11,00, ). When up/doun is low, the counter counts down (00,11.10.01.00, ). Part A Complete the state diagram below by adding all required transition arcs with input annotations. Output annotations are not required since they correspond to the new state. state state 00 01

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110
We need to generate a PWM signal with frequency of 2 KHz, and duty cycle of 20%. The clock frequency is 1 MHz and the counter is configured in count-up-down mode. Determine the values that we need to write in LOAD and COMPARE registers. You can use either pwmA or pwmB.
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Draw logic diagram for half adder and full adder circuit using Logisim Software
Which statement describe a digital signal? a. is a smoothly and continuously varying voltage or current. b. will take on finite set of voltage levels. c. take on all possible values of amplitude. d. can have an infinite number of values in a range
Write hamming code for the data 0011 for the (i) Even parity (ii) Odd parity. Explain the process briefly
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
2) Convert Hexa-decimal to Octal a. 7E6A(16)=?(8) b. C350(16)=?(8) c. 9E36.7A(16)=?(8) d. EADD.EBEF(16)-?(8)