support A as shown in Figure Q.5. (a) determine the final bending moments at supports A and C and at joint B, (b) determine the support reactions, (c) sketch the bending moment diagram for the frame ABC indicating all salient values. Hint: Determine Vc and MA using the moment distribution method and use static equilibrium to solve for the other unknown reactions.

support A as shown in Figure Q.5. (a) determine the final bending moments at supports A and C and at joint B, (b) determine the support reactions, (c) sketch the bending moment diagram for the frame ABC indicating all salient values. Hint: Determine Vc and MA using the moment distribution method and use static equilibrium to solve for the other unknown reactions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The value of M in the beam ABC shown in the figure is such that the joint B does not rotate. 30 kN/m aj v vvv v vy 4 m FR B The value of support reaction (in kN) at B should be equal to 6 m
QUESTION 1 METHOD OF CONSISTENT DEFORMATION. For the frame shown below, determine the reactions at the supports (MA Ax Ay Cy) using Method of Consistent Deformation. El is constant. 500 lb/ft В 3 k A 10 ft 10 ft C
2.5 A hon-uniform, rigid jointed frame is fixed at supports A and D as shown in Figure Q.5. where EI is constant for both members. For the loading indicated, and using the moment distribution method, (a) determine the final bending moments at supports A and D and at joint B, (b) determine the support reactions, (c) sketch the bending moment diagram for the frame ABD indicating all salient values. Hint: wa? FEMAB = - 12L2 noted below. For a span under part udl starting at left hand support, the FEM are: (6L? – 8aL + 3a2) & FEMBA = + wa3 (4L- 3a) as 12L2 UDL on left side wa? 1212 (61-8a1+3a*) w (sen) 12L2 (4L-3a) MRA MA B 6 kN/m 24 kN B 4 m 2 m 2 m 5m A Figure Q.5
Figure shows a statically determinate beam under distributed loading conditions where C is the constant. 2x x? q(x) = C(- L AB A 2L/3 L/3 RA RB Figure 2 a) Determine the resultant of the distributed load where C is constant. Submit part Unanswered b) The magnitude and direction of the reactions at support B. Submit part Unanswered c) The magnitude and direction of the reactions at support A.
Reactions have been calculated for the beam AB shown in the figure. The shear force at location X (4m to the right of A) is most nearly equal to 6kN 3kN/m A i B VA = 8.4kN Vg = 9.6kN 4m 2m 4m 2m 2m
Problem 2: For the shown beam, 40 N 150 N 250 N knowing that distance d = 1.0 m: a. Calculate the reactions at the supports on the opposite beam. ......
The beam of flexural rigidity EI is clamped at both ends and subject to a uniformly distributed load extending along the region BC of length 0.60L. If w = 10 KN/m and L = 4 . What is the value of the reaction RA in KN? Three decimal places.
Neglecting friction and the weights of the members, compute the following: magnitude of the pin reactions at A and C for the folding table shown. Use L = 350 N/m 1. Pin reaction, Ay 2. Pin Reaction, Cy 3. Pin Reaction, Cx
For the continouus beam loaded as shown in figure. Assume El is constant. Using the method of moment distribution. a. (20%) Comute the end moments over the spports b. (10%) Compute the reactions at gthe supports c. (10%) Draw the shear and bending-moment diagrams for the beam. d. (10%) What is the maximum negative and positive moments?. P = 180 kN P = 90 kN w =10 kN/m A D 4m 3m 4m 8 m 6m
Q1. (а) Figure Q1(a) shows a beam loaded with a point load and a partially UTM uniform distributed load. respectively. support at A and B are roller 3 UTM The M 5 UTM (i) Draw the free body diagram of the structure. * UTM UTM Determine the support reactions at A and B by taking the (ii) structure in equilibrium condition. ITM O UTM - UTM 5 UTM O UTM 30kN 30° 10KN/m F = 840 N 2m 24 m 2m 4m A \3 m G UTM 15 m 2 m STMUTM 5 UTM FIGURE Q1(a) 10 ni FIGURE Q1(b) 一

Q/Using the method of consistent deformation, find support reaction of the frame shown; assume EI= constant. 10kN/m B A 5m C 3m
Determine the reactions at A and B for the beams loaded as shown in Figure (a)-(c) below.Beam weight may be neglected in all cases.