For the continouus beam loaded as shown in figure. AssumeEl is constant. Using the method of moment distribution.a. (20%) Comute the end moments over the spportsb. (10%) Compute the reactions at gthe supportsc. (10%) Draw the shear and bending-moment diagrams for the beam.d. (10%) What is the maximum negative and positive moments?.P = 180 kNP = 90 kNw =10 kN/mAD4m3m4m8 m6m

Answered: Image /qna-images/answer/7dcfd73a-f4bf-4882-90bb-727ac36bf4e9.jpg

(20%) Comute the end moments over the spports (10%) Compute the reactions at gthe supports (10%) Draw the shear and bending-moment diagrams for the beam. (10%) What is the maximum negative and positive moments?.

(20%) Comute the end moments over the spports (10%) Compute the reactions at gthe supports (10%) Draw the shear and bending-moment diagrams for the beam. (10%) What is the maximum negative and positive moments?.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please Calculate the bearing reaction of a beam structure in the figure. Assume that the value of EI is constant throughout the beam
3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young's modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work. (а) (b) Based on Q2(a), suggest an appropriate steel bar measurement.
Problem 3: For the beam shown in Figure 3. A. Find the reaction support B (R) B. Find the reaction support D (Rp)
Q/Using the method of consistent deformation, find support reaction of the frame shown; assume EI= constant. 10kN/m B A 5m C 3m
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
1.(a)For the beam with built-in ends, determine (b) all the support reactions; and(b) the displacement at the midpoint C. (Hint: Use symmetry.) 2.(a) Determine the equation of the elastic curve for the overhanging beam; and (b) calculate the value of EIv midway between the supports. 3.Determine all the support reactions for the propped cantilever beam shown in the figure. 4.For the beam with built-in ends, determine (a) all the support reactions; and(b) the displacement at the midpoint C. (Hint: Use symmetry.) 5.The beam ABC has a built-in support at A and roller supports at B and C. Find all the support reactions.
Determine the reactions at each support of the beam shown in the figure. EI is constant.
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
A cantilever beam is free of support at point A and is clamped at the point B, as shown in the Figure Q4 below. Calculate the support reaction force and moment for the non-uniformly distributed load, where w =74 N/m and L = 6 m. The downward direction is denoted as positive direction in force and the anti- clockwise direction is defined as positve in moment. For all numerical answers, answer to within 3 decimal places. A v y -L- Figure Q4: A cantilever beam under non-uniformly distributed load
A propped cantilever beam AB of a length L carries a concentrated load P acting at the position shown in the figure. B/ ΜΑ RA RB L Determine the reactions RA, RB, and MA for this beam. (Solve by the method of superposition. The beam has constant flexural rigidity EI. Assume that the +x-axis is to the right, the +y-axis is up along the page, and the +z-axis is out of the page. Use the statics sign convention. Use the following as necessary: L, a, b, and P.) RA = RB = MA = Also, draw the shear-force and bending-moment diagrams, labeling all critical ordinates, including maximum and minimum values. (Submit a file with a maximum size of 1 MB.) Choose File No file chosen ●●●