Springs AB and CD have a stiffness of ka = 8 lb/in and kçp = 4 lb/in, respectively, and both springs have an un-stretched length of 12 in. If the 5-lb collar BC is suddenly released from rest in the position shown, determine how far the collar travels to the left before it momentarily comes to rest. Take the coefficient of kinetic friction between the collar 30 B 14 in 10 in and guide rod AD as 4, = 0.3.

Springs AB and CD have a stiffness of ka = 8 lb/in and kçp = 4 lb/in, respectively, and both springs have an un-stretched length of 12 in. If the 5-lb collar BC is suddenly released from rest in the position shown, determine how far the collar travels to the left before it momentarily comes to rest. Take the coefficient of kinetic friction between the collar 30 B 14 in 10 in and guide rod AD as 4, = 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. 21.0 kN А 3.0 m в 3.0m 3.0 m 2.2 m 3.0 m 3.0 m E Answers: BC = i kN BE = i kN EF = i kN
The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-sectional area of 25 mm -7 2 and a =11.7 *10 m/ m.°C. E A 15 KN 0.2 m + 0.2 m 0.4 m of
The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 50°C. Neglect the weight of bar ABC. Use a = 11.7 x 10/°C and E = 200 GPa. A= 1200 mm A=300 mm 1.2 m 0.9 m 君 12 m
The system lamp has a mass M and is supported by the six strings shown. The length of the chords and the horizontal distance ED are constant, point E remains fixed but the vertical distance ED can vary. a) If in the position shown the chord BC is horizontal, calculate the angle ? to maintain equilibrium, consider the mass M = 10 kg. b) Explain what happens to the magnitude of the stresses when point D moves.
H.W3: Analysis the structure shown in figure, El is constant W=20 KN/m P =40 KN B C 4m 3 3
The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-sectional area of 25 mm 2 -7 and a =11.7 *1o'm/ m-°C. 15 KN 0.2 m 0.2 m 0.4 m
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
3
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
QI For the portal frame as shown in Figure QI, determine the following. (a) The determinacy of the frame (b) The reaction forces at all supports and pin at point D. (c) The internal forces at point B. 10 kN/m 3 m 15 kN 4 m 6 m 7 m 7 m
The torques shown are exerted on pulleys A and B which are attached to solid circular shafts AB and BC. In order to reduce to total mass of the assembly, detemine the smallest diameter of shaft BC for which the largest shearing stress in the assembly is not increased. TA = 300 N m 30 min B TH = 400 N- m 46 nn