specified. Dead load: Uniform load of 60 kN/m Live load: Uniform load of 35 kN/m and two concentrated loads 300 kN and 150 kN, respectively, that are separated by 2.0 m. Consider Design Factored Load: 1.2 DL + 1.6 LL. A -2 m- Determine maximum positive and negative moment at point C for the loading B -4 m- C -4 m- Mmax = Mmax =

specified. Dead load: Uniform load of 60 kN/m Live load: Uniform load of 35 kN/m and two concentrated loads 300 kN and 150 kN, respectively, that are separated by 2.0 m. Consider Design Factored Load: 1.2 DL + 1.6 LL. A -2 m- Determine maximum positive and negative moment at point C for the loading B -4 m- C -4 m- Mmax = Mmax =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is loaded as shown in Figure AN-02. Assume El to be constant. A. C 5 m PORGARÍGUINTESTMILKSKORTERIG ISHOCKERAT 3 m 3 kN B FIGURE AN-02 find the value of Kab NAB 4 kN/m 1. Which of the following most nearly gives the fixed end moment at B due to the concentrated load, FEMBA= [Select] 5 m 2. Which of the following most nearly gives the distribution factor at B for member [Select] AB in percent, DEBA 3. Which of the following most nearly gives the moment at B in KN-m, Mb = [Select] 4. Which of the following most nearly gives tire modified stiffness factor, Kat member AB, use l-1 to [Select] C 5. Which of the following most nearly gives the modified stiffness factor, K at member BC, use l-1 to
6 kN/m 3 kN/m A В 4.5 m 1.5 m Q1- The beam shown is subjected to two types of distributed loading. Support A is a pin, support B is a roller. Determine the following: (a) The Total load is carried by the beam is . kN (b) Vertical Force Reaction at support B, By is kN (c) Vertical Force Reaction at support A, Ay is kN
Question 2 Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and pinned at A. The frame carries 200 kN horizontal point load acting at the middle of member AC, 50 kN point load at point E and 50 kN/m uniform distributed load on member BC. El is constant. majum (b) 2m 2 m 50 kN/m 200 kN 6 m Figure Q2: Frame [Rajah Q2: Kerangka] 6 m D Next, calculate the fixed-end moment (FEM) for all members. w 1000 50 kN (a) For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for each member. 2 m
1. A beam is supported by two springs as shown below. The spring at A has spring constant KA = 200000 N/m while the spring at B has spring constant kB = 400000 N/m. The beam is loaded by a uniform distributed load of 500 N/m and a point load at C of 1000 N. 1000N A 500 N/ I ка 2M 1 SB ufi L кв экім- a. Assuming the beam is RIGID, calculate the deflection at point C. b. Assuming the beam is DEFORMABLE with EI = 200000 N-m², calculate the deflection at point C.
Find the maximum live load can be applied to the beam shown in the figure (3-1). Use 3$25 for positive moment 4$16 for negative moment. Where fe' = 33 Mpa, fy = 414 Mpa. 7 m 3 m OST 300
The bridge truss shown carries the following uniform live load and concentrated live load. в с D A B E 3m K F G H J SO8m W(LL) P(LL) 15 110 Calculate the following: 7. Maximum force on member GH
Find the largest load P, that can be carried safely by the system below. Pin A is double shear. Given: Tall of pin A = 100 MPa %3D Sall on the rod BC = 20 MPa diameter of pin A, Øpin A = 10 mm diameter of the rod, Ørod = 20 mm C P -1 m -1 m -1 m 1 m B 0.75 m
Solve for the A ΕΙΔ 400 N/m 400 N/m m. m 2m Using Conjugate, beam method 2.3m EI A @pt. C 2.2m
The beam AB is supported by two concentrated loads against FA = 130 kN and FB = 203 ww KN forces, respectively. Please determine, a) distributed load of @a and b) distributed load of oB. FA F8 a = 0.6 m 0.3 m B WA 1.8 m ANSWERS @, (EV / m) o,(N/ m)
ASAP
mple Problem: Determine themagnitude T of the tension in the supporting eable and thee agnitude of the force on the pin at A for the jib crane shown. The beam AB is a standard 0.5 m I-beam with a mass of 95 kg per meter of length. on
Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and pinned at A. The frame carries 200 kN horizontal point load acting at the middle of member AC, 50 kN point load at point E and 50 kN/m uniform distributed load on member BC. El is constant. (a) (b) 2 m 2 m 50 kN/m 200 kN 6 m Figure Q2: Frame [Rajah Q2: Kerangka] 6 m 1041 Next, calculate the fixed-end moment (FEM) for all members. 50 KN 2m E For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for each member.