Solve for the reactions at A, B and forces in members AB, BC and AC. (Ray~13 kN, Rß~7 kN, FAB~ 17 kN, FAC~20 kN, FBC ~ 18 kN - A B 20 m C 25 m 20 kN 50 m

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: Worksheet 6-3 00 1. Type of view 2. Type of view 3. Type of view 4. Type of view 5. Is view 4 easier…

A: Solution: Given Data:

Q: Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave…

A:

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: The . drawings are the drawing that include all the information and instructions needed for the…

A: Drawing: A drawing is a representation of parts or assemblies by lines according to some certain…

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: Define the term layout and briefly explain the purpose for layout.

A: Given Data : Layout

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: In Figure below, the main issue is with the leader representing which item?

A: Given:- An engineering drawing To find: Which representation is wrong

Q: 11) Define the cornering stiffness.

A:

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: What is angular indexing and block indexing?

A: Angular indexing:  It is similar to simple indexing except that in this process, instead of rotating…

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: Okay I did everything you did but the only thing I didn't do was take away 10 degrees from my…

A:

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: Q3: Mark the Following True or False 1. Hatching of different components is done on same direction.…

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: In creating orthographic views, each view must:

A:

Q: Subparts 1, 2, and 3.

A:

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: 1. Write the procedure for shaper process.

A: Shaper process is the process in which unwanted metal surface is removed by a single-point cutting…

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: Differentiate 1. Method of removal 2. Kind of work material 3. Type of cut EDM, USM, and ECM as to

A: Wire EDM  is an electro thermal manufacturing technique in which a thin single strand metal wire…

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.