Situation # 4: The pump shown draws water from the reservoir A at elevation 10m and lifts it to reservoir B at elevation 60m. The loss of head from A to 1 is two times the velocity head in the 200mm diameter pipe and the loss of head from 2 to B is ten times the velocity head in the 150mm diameter pipe. Determine the relate horsepower of the pump and the pressure heads at 1 and 2 in meters when the discharge is 0.03m/sec. El. 60m Ei. 30 m 500 m 200 rm 2l. a m FUMP

Situation # 4: The pump shown draws water from the reservoir A at elevation 10m and lifts it to reservoir B at elevation 60m. The loss of head from A to 1 is two times the velocity head in the 200mm diameter pipe and the loss of head from 2 to B is ten times the velocity head in the 150mm diameter pipe. Determine the relate horsepower of the pump and the pressure heads at 1 and 2 in meters when the discharge is 0.03m/sec. El. 60m Ei. 30 m 500 m 200 rm 2l. a m FUMP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure FM-P-113. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. Choices are in the images Determine: Power delivered by the pump in kW Pressure head at point 1 in m. Pressure head at point 2 inm.
A pump draws water from reservoir A and lifts it to reservoir B as showm, The head los from reservoir A to pipe 1 is 3 times its velocity head and the head loss for pipe 2 to reservoir B is 20 times the velocity head. When the discharge is 20 L/s a) Compute the horsepower output of the pump in kW b) Compute the pressure head at pipe 1 c) Compute the pressure head at pipe 2 EL Om pipe 1 150 mm pipe 2 100 mm -EL-20 m EL 240 m
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
A pump draws water from reservoir A and lifts it to reservoir B as shown. The loss of head from A to 1 is 3 times the velocity head in the 150mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100mm pipe. When the discharge is 20 liters/sec. Compute the pressure head at point 1 and 2. B EL240m ELO 150 mm EL-20m • ura 001
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
Calculate the mechanical power [hp] required on the pump shaft considering the hydraulic system Shown. The pipe is made of commercial steel (roughness = 0.0002 ft) and has two different diameters, up to the pump inlet the pipe is 2 inches with a length of 100ft and from the pump outlet the pipe is 4 inches with 400ft. All elements are screwed The flow rate circulating through the system is 0.5 ft3/s and the efficiency of the pump is 85%. The density of water is 1.94 slug/ft3 and has a viscosity kinematics 1.1x10-5 ft2/s
10.The 600-mm Ø pipe shown conducts water from reservoirA to a pressure turbine which discharges through another600-mm Ø pipe into the tail-race at B. The loss of headfrom A to 1 is 5 times the velocity head in the pipe andthe loss of headfrom 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 700 li/s. a.Compute the hp given up by the water to the turbine. b.Compute the pressure head at 1. c.Compute the pressure head at 2.
In the system shown in the figure, the pump moves 220 It/s of water through a system of horizontal pipes to the closed reservoir. The head of pressure at the pump inlet is -1.2 meters and at the outletof 58 meters. Determinea) The pressure on the free surface of the water in the tank,b) Draw the total line ofpressure and piezometric line. Use a hinge disc type foot valve.
3. A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 700 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 100 mm dia. 45.0 m 540 m
A pump is required to draw 50 lps of water (SG = 0.988) from reservoir A, with static suction lift of 4.5 m, to reservoir B, with static discharge head of 15 m. the pipe in the suction line is a 6” nominal diameter, sch. 40, and 80 m long. The pipe in the discharge side is a 4” nominal diameter, schedule 40, and 150 m long. The fittings and valves installed in the suction line are one-foot valve, one standard elbow, and one gate valve: and in the discharge line are one check valve, one gate valve, and two standard elbows. Assuming an absolute roughness of 0.24 mm for a cast iron pipe, and an absolute viscosity of water of 0.01002 Poise. Neglecting the head losses in the foot valve and at the exit in the discharge reservoir. Determine the pump brake power if the pump efficiency is 82
3. Water is being pumped at 2.5ft3/s. The head loss between points 1 and 2 is 9ft and the power rating of the pump is 25hp. If the pump has an efficiency of 35%, solve the differential height of the mercury in the manometer (SG = 13.6). D₁ = 3 in 5 ft Pump h? D₂ = 6 in 8-1₂ Mercury