Water is pumped from a supply reservoir to a ductile ron water transmission line. The high point of the ransmission line is at point A 1 km downstream of the supply reservoir and the low point of the ransmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the

Water is pumped from a supply reservoir to a ductile ron water transmission line. The high point of the ransmission line is at point A 1 km downstream of the supply reservoir and the low point of the ransmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B. Determine the discharge in the pipe and the pressure at point Water T 1.5 m 3.5 m B 40 cm diameter -20 cm-diameter nozzle
3. A pump is used to transport water at the rate of 0.075 m³/s from a reservoir 20 m above the pump to a free discharge 35 m above the pump. The pressure on the intake side of the pump is 150 kPa and the pressure on the discharge side is 450 kPa. All pipes are commercial steel of 15 cm inner diameter. Determine (a) The head supplied by the pump (b) The total head loss between the pump discharge and point of free discharge. Z₁=20 m 1 P₂ = 150 kPa 2 面 3 D=15 cm A P3=450 kPa 4 Free Discharge Z4 = 35 m
Determine the available NPSH for the system shown in Fig. 13.38 (b). The fluid is water at 80°C and the atmospheric pressure is 101.8 kPa. The water level in the tank is 2.0 m below the pump inlet. The vertical leg of the suction line is a DN 80 Schedule 40 steel pipe, whereas the horizontal leg is a DN 50 Schedule 40 pipe, 1.5 m long. The elbow is of the long-radius type. Neglect the loss in the reducer. The foot valve and strainer are of the hingeddisk type. The flow rate is 300 L/min.
A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice point- ing upstream and other perpendicular to it. The mean velocity in the pipe is 0.80 of the central velocity. Find the discharge through the pipe if the pressure difference between the two orifices is 60 mm of water. Take the co-efficient of pitot tube as C = 0.98.
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
A pump is used to draw water from an open reservoir to an open tank on thetop of a building. The discharge flow rate is 50 lps. The static suction head of the pump is6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suctionline is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in thedischarge line is 6 inches nominal diameter and 65 m long. The fittings and valvesinstalled in the suction line are the following: two 90o standard elbow and one gate valve.For the discharge line, are the following: one check valve, one gate valve, and three 90ostandard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of82 %. Determine: a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
choose the correct answer B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above
3)a: For the figure below, find the discharge in pipe, neglect the minor losses only. (e-0.001m, D-Im, L-600m, u-1.307*10 m/sec). LAS 5m 2 1.96 D. b: In a pipe of 300 mm diameter the maximum velocity of the flow is found to be 2 m/s. If the flow in the pipe is laminar, determine: 1) The average velocity and the radius at which having the same velocity magnitude as the average velocity. 2) The velocity at 50 mm from the wall of the pipe. 5964 11.62
At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank. a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient
At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank.a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient.
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
A pipeline having a diameter of 250 mm has a rate of flow of 0.30 m³/sec. from point 1 to 2, with 2 lower than 1. A gate valve is connected at a point 3 near point 2. The elevation of point 2 is 100 m. O Compute the elevation of 1 when the gate valve at 3 is closed and the difference in pressure P2 - P1 = 78 КРа. ® Compute the head loss from 1 to 2 when the gate valve at 3 is open and the difference in pressure Ри- Р2%3D 160 kРа. 3 Compute the length of pipe from 1 to 2 if f = 0.020.