Situation 3: As shown in the figure block D is used to support the 100-kg uniform pole ABC in the position shown. 1. 2. 3. -7.5 m- B P=0.2 -3 m -1=0.2 D 1 m 4 m Find the normal force at point B. Find the frictional force at point B. Calculate the weight of the lightest block D than can be used to support the pole against impending sliding. Calculate the weight of the lightest block D than can be used to support the pole against impending tipping. 4. 5. Calculate the weight of the lightest block D than can be used to support the pole.

Situation 3: As shown in the figure block D is used to support the 100-kg uniform pole ABC in the position shown. 1. 2. 3. -7.5 m- B P=0.2 -3 m -1=0.2 D 1 m 4 m Find the normal force at point B. Find the frictional force at point B. Calculate the weight of the lightest block D than can be used to support the pole against impending sliding. Calculate the weight of the lightest block D than can be used to support the pole against impending tipping. 4. 5. Calculate the weight of the lightest block D than can be used to support the pole.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 5: In the figure shown below, u = 0.3 for all contact surface. ma = 150 kg, mb = 200 kg P B 40 a. If e = 0, find P for motion to impend to the right. b. If e = 0, find P to just prevent the motion.
The 679-N force is applied to the 114-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.77 = 0.60 Answer: F= i 26° N P = 679 N
Situation 3: As shown in the figure block D is used to support the 100-kg uniform pole. ABC in the position shown.. 1. 2. 3. 7.5 m- A=0.2 -3 m- -0.2. D 11 C 4 m . Find the normal force at point B. Find the frictional force at point B. Calculate the weight of the lightest block D than can be. used to support the pole against impending sliding..
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is represented by the 2 kN load shown. a. Produce shear and moment diagrams for the supporting frame ABC. b. Calculate the horizontal deflection of the point of loading. Assume that frame ABC has bending stiffness El = 2.7×105 Nm². 0.9 m A 0.6 m C B 2 KN
The figure shown is a cross-section of the beam on the fixed support of a propped beam that has a moment of 72 kN-m. Determine the following: a. The location of the centroid from the extreme tension fiber. The moment of Inertia of the cross-section. The bending stress at the extreme compression fiber. d. Show the force and moment check of the beam. b. c. 70 mm 50 mm- 100 mm: 50.0000 130 mm- 100.0000 -350 mm- 100 mm-
Determine the change in length, breadthand long,semm thickness f a steel bar which is 4 m wide and 20 mm thick and is subjected to axial pull of KN in the divechion of leng th. E = 2xlo/m, = 0.3
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A L 20 N B 1.5W, N/m Figure 1: Overhang beam Find the deflection at the middle of the segment AB L C Set wo = 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m Figure 1: Overhang beam Find the equation of the elastic curve for the segment AB. L C - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
P = 7 kN 10 mm- 15 kN • m 10 mm 150 mm D В 150 mm 1.0 m 1.0 m 1.0 m The simply supported beam is loaded as shown. Obtain the bending moment function and draw its diagram. Determine the magnitude and location of the maximum bending stress. What is the largest value of the force P that can be applied if the allowable bending stress 250 MPa.
Specifications of the steel rod at B. L=2 meters diameter= 25 mm E= 200 GPa Show complete solution 1. Draw the shear force and bending moment diagrams. 2. Determine the deflection at A