mass of 400 g shown in below figure is connected to a light spring whose force regular is 5kN/m. it's miles unfastened to oscillate on a horizontal frictionless track. If the mass is displaced 10cm from equilibrium and released from rest, locate (a) duration of movement, (b) most pace of the mass. (c) maximum acceleration of the mass, and (d) equations for displacement, speed and acceleration as characteristic of time

mass of 400 g shown in below figure is connected to a light spring whose force regular is 5kN/m. it's miles unfastened to oscillate on a horizontal frictionless track. If the mass is displaced 10cm from equilibrium and released from rest, locate (a) duration of movement, (b) most pace of the mass. (c) maximum acceleration of the mass, and (d) equations for displacement, speed and acceleration as characteristic of time

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure shown, what is the moment that this force exerts about point A? F = 75 N 30 deg B 8m A 60 deg |
The step pulleys shown in the figure below are connected by a crossed belt. If the angular acceleration of C is 2 rad/s^2, what time is required for A to travel 180ft from rest? Through what distance will D move while A is moving 240ft/s? Answer for tA should be 6.71 sec and SD should be 180 ft
9. Two balls A and B of masses 100 grams and 300 grams respectively are pushed horizontally from a table of height 3 meters. Ball has is pushed so that its initial velocity is 10 m/s and ball B is pushed so that its initial velocity is 15 m/s. a. Find the time it takes each ball to hit the ground. b. What is the difference in the distance between the points of impact of the two ball on the ground? Formula Vx = Vo cos 0 Vy = Vo sin 0 – gt x = Vo cos et y = Vo sin Ot – gt2
Calculate ther and ecomponents of acceleration. Answers: The particle of mass m= 3.6 kg is attached to the light rigid rod of length L=0.71 m, and the assembly rotates about a horizontal axis through Owith a conatant angular velocity 8 = w =2.0 rad/a. Determine the force Tin the rod when 8 = 21". The force Tis positive if in tanaion, negative if in compression.
Part A The magnitude of the force exerted on the wrench is 20 lb (Figure 1). What moment does the force exert about point P? 2.40 in 5.20 in 20 Express your answer in inch-pounds to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. MP = ΑΣΦ 1 vec ? in-lb
For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the horizontal slotted arm which is elevated in the y-direction at the constant rate of 5.0 in./sec. All measurements are in inches and seconds. Calculate the velocity v and acceleration a of pin A when x = 4.0 in. Part 1 When x = 4.0 in., what is the value of y? Answer: y = x = y²/7 i in.
As a train accelerates uniformly it passes successive 800 meter marks while traveling at velocities of 3 m/s and then 12 m/s. [Select] ✓(a) For the first mark of the journey, what is the acceleration of the train in m/s². [Select] [Select] (b) Determine the train's velocity when it passes the next mark in m/s. (c) Determine the time it takes to travel the 1.6-km distance in seconds.
2-8 A fluid that occupies a volume of 24 L weighs 225 N at a location where the gravitational acceleration is 9.80 m/s?. Determine the mass of this fluid and its density.
Part A The assembly consists of two 15-kg bars which are pin connected The bars are released from rest when 0 = 60°. The 5-kg disk at C has a radius of 0.5 m and rolls without slipping. (Figure 1) Determine the angular velocity of the bar ABat the instant 0 = 30° , measured clockwise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. Ivo AEO| 1t vec WAB = 1.13 rad/s Figure 1 of 1 > Submit Previous Answers Request Answer X Incorrect; Try Again; One attempt remaining 3 m. 3 m Part B IC Determine the angular velocity of the bar BC at the instant 0 = 30° , measured counterclockwise Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise.
The figure shown is formed of 1/8 -in.-diameter steel wire. Knowing that the specific weight of the steel is 490 lb/ft3 , determine the mass moment of inertia of the wire with respect to each of the coordinate axes.
When the bar is at the angle, the rod is rotating clockwise with constant angular velocity w. (Figure 1) Figure 10 ft SA D w, a 10 ft Part A Determine the velocity of the weight A at this instant. The cord is 20 ft long. Express your answer in terms of some, all, or none of the variables 0, w, and the appropriate constants. VA = Submit VAΣ vec Request Answer < Return to Assignment Provide Feedback ?
two pulleys connected by a cord with a speed of 4m/s is shown below. The acceleration of A is 300 m/s^2. What is the acceleration of B at this same instant?