Situation 11: As shown in the Figure, three steel wires, each 0.05in? in area, are used to lift aload W = 1,500lb. Their unstressed lengths are 74.98ft, 74.99ft, and 75.00ft. E = 29x106 psi.w34. Which of the following most nearly gives the stress in the longest wire?a. 10,194.03psib. 12,099.13psi35. Which of the following most nearly gives the stress in the shortest wire?a. 9,874.22psib. 13,868.69psi36. Which of the following most nearly gives the stress in the intermediate wire?a. 8,026.65psib. 10,102.52psic. 6,131.66psid. 8,342.87psic. 5,866.17psid. 11,554.61psic. 13,939.80psid. 9,999.66psi

Answered: Image /qna-images/answer/899974c1-d6a6-481f-9994-90b2a86d8f0b.jpg

Answered: Situation 11: As shown in the Figure,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three cables having an area of 0.05 in^2 each is carrying the load W as shown. With no stress, the original lengths of the cables are 74.99 ft, 75.00 ft, and 74.94 ft. E = 29 x 10° psi Calculate for the stress in the intermediate wire. Choices: a. 8,026.65 psi b. 9,999.66 psi c. 19,939.80 psi d. 10,102.52 psi 1500 lb
A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 3000 N. If the stress is not to exceed 130 MPa at -20°C, find the minimum allowable diameter of the rod. Use a=11.7 x 10-6/°C and E = 200 GPa. Select one: O a. 10.24 mm O b. 9.92 mm O C. 16.53 mm O d. 13.22 mm
A bronze tire (thickness=12mm, width= 110 mm, internal diameter=800 mm) was heated and shrunk onto an 800.5 mm diameter bronze wheel. E = 83 GPa. 1. Find the Tensile stress in the tire. a. 51.8 MPa b. 121 MPa c. 107 MPa d. 125 MPa 2. Find the compressive force bet the tire and the wheel when pinched. a. 1.56 MPa b. 3.53 MPa c. 2.25 MPa d. 3.75 MPa 3. Find the minimum required wheel thickness when allowable stress is 124 MPa and the compressive stress is 1.5MPa. a. 4.0 mm b. 4.25 mm c. 3.52 mm d. 4.84 mm
Two plates 16 mm thick are joined by a double riveted lap joint. The pitch of each row of rivets is 90mm. The rivets are 25 mm in diameter. The permissible stresses are as follows : σt = 140 MPa ; τ = 110 MPa and σc= 240 MPa Find the efficiency of the joint. [Ans. 53.5%]
12mm dia 18mm dia. P=12 kN 12mm dial 2 m 2. Three steel cable jointly support a load of 12kN. The diameter of the middle bar is 18mm and the diameter of each outer cable is 12mm, The tension in the cable are adjusted so that each cable carrries one third of the total load(4KN). Later it was increased by 9kN to a total of 21 kN. a. What percent of the total load is now carried by the middle cable? b. Determine the stress of the middle cable c. Determine the stress of outer cable..
1. Two plates 16 mm thick are joined by a double riveted lap joint. The pitch of each row of rivets is 90 mm. The rivets are 25 mm in diameter. The permissible stresses are as follows : o, = 140 MPa;t = 110 MPa and Oc = 240 MPa. Find the efficiency of the joint. [Ans. 53.5%]
5. A steel bolt through a 25-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross- sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 106 psi, coefficient of thermal expansion = 6.5 x 10-6/°F For aluminum: E = 10 x 106 psi, coefficient of thermal expansion = 13.0 x 10-6/°F a. Find the thermal deformation (in inches) of the bolt. b. Find the thermal deformation (in inches) of the aluminum tube. c. Find the stress (in psi) induced in the bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change. 1911 EDI
A double-decker train. EXERCISES 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the diameter of the connecting rod at its thinnest part, if the permissible tensile stress is 35 N/mm. [Ans. 50 mm) 2. The maximum tension in the lower link of a Porter governor is 580 N and the maximum stress in the link is 30 Nimm. If the link is of circular cross-section, determine its diameter. (Ans. 5 mm) Тор Contents Simple Stresses in Machine Parts 117 3. A wrought iron rod is under a compressive load of 350 KN. If the permissible stress for the material is 52.5 Nimm, cakculate the diameter of the rod. JAns. 95 mm) 4. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if the stress in the wire is not to exceed 100 N/mm. (Ans. 8 mm) 5. A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6 bolts. Calculate the diameter of the bolt if the maximum stress in the tie bar is…
6. What is the stress, in ksi, in the 0.040 in. diameter guy wire if the tension in the clothes line is 30 lb? Use a = 2.5 ft, b = 3.5 ft, and c = 6 ft. a. b. b 50.4 60.4 a Clothes line Guy wire C. d. 70.4 Answer is not among the choices
1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 GN/m. [80 MN/m², 0.12mm] 2. (A). A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN. What will be the stress in the bar? What further increase in load is possible if the stress in the bar is limited to 225 MN/m?? [106 MN/m²; 45 kN]
Question 5 A lead of 5kN is to be raised using a steel wire. Find the minimum diameter of the wire required to raise the load if the yield stress of steel is 300MP.. 5kN
19. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in steel wire, which is 10 inches long? Assume deformation to be vertical. Use E = 30 x 106 psi. 4.5 in a. b. 0.0238 0.0431 a. b. 8 mm 3/8 inch Steel wire 25 KN Nixed 20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? 2 in. 12 mm C. 0.0581 d. 0.0631 C. d. 10 mm 1/2 inch P 7.5 mm 12 mm 7.5 mm 25 KN

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS